mh102-pcb ETC-unknow, mh102-pcb Datasheet

mh102-pcb

Manufacturer Part Number

mh102-pcb

Description

High Dynamic Range Mmic Mixer

Manufacturer

ETC-unknow

Datasheet

1.MH102-PCB.pdf (4 pages)

Current page: 1 of 4
Download datasheet (161Kb)

Product Features

Specifications

Test conditions unless otherwise noted: RF / IF = 1900 / 300, 2200 / 150, and 2200 / 300 MHz with a low-side LO at +17 dBm in a downconvertering applicaion at 25°C.

Input IP3 was measured with two tones with an input power of +2 dBm/tone separated by 10 MHz.

Absolute Maximum Ratings

1. Operation of this device above any of these parameters may cause permanent damage.

2. Total sum of LO port and RF port power should not to exceed +23 dBm.

WJ Communications, Inc. • Phone: 1-800-WJ1-4401 • FAX: 408-577-6620 • e-mail: sales@wj.com • Web site: www.wj.com

•

Parameter

Frequency Range:

SSB Conversion Loss

Noise Figure

Input IP3

Input P1dB

Isolation:

Return Loss:

LO Drive Level

Parameter

Operating Case Temperature

Storage Temperature

Maximum Input LO Power

+32 dBm Input IP3

No External Matching Elements

RF 1900-2200 MHz

IF 150-300 MHz

Low Cost SOIC-8 Package

UMTS Up/Down Converter

1930-1990 MHz Up Converter

Required

L-R

L-I

R-I

RF Port

LO Port

IF Port

MH102

High Dynamic Range MMIC Mixer

Units

MHz

dBm

Product Description

The MH102 is a passive GaAs MESFET mixer that

provides high dynamic range performance in a low

cost SOIC-8 package. WJ’s MH102 uses patented

techniques to realize greater than +30 dBm Input

IP3 at an LO drive level of +17 dBm.

This single monolithic integrated circuit does not

require any external baluns, bias, matching, or

decoupling elements. The on-chip diplexer affords

good matching on the RF and IF ports.

Typical applications include frequency up/down con-

version, modulation and demodulation for receivers

and transmitters used in 3G UMTS systems.

-65 to +100°C

-40 to +85°C

+21 dBm

Rating

Minimum

1900

1600

+28

150

Typical

+32

+16

+17

9.0

9.5

Ordering Information

Part No.

MH102

MH102-PCB

Specifications and information are subject to change without notice.

Maximum

2200

2050

10.5

300

The Communications Edge

Description

High Dynamic Range MMIC Mixer

(Available in tape and reel)

Fully Assembled Application Circuit

Functional Diagram

Condition

Function

Ground

Product Information

1,3,4,6,8

Internal

Diplexer

Pin No.

February 2004

™

Related parts for mh102-pcb

mh102-pcb Summary of contents

Page 1

... Function Ground Maximum Condition 2200 2050 300 10.5 Part No. Description MH102 High Dynamic Range MMIC Mixer (Available in tape and reel) MH102-PCB Fully Assembled Application Circuit Specifications and information are subject to change without notice. ™ Internal 8 Diplexer Pin No 1,3,4,6,8 February 2004 ...

Page 2

... MH102 High Dynamic Range MMIC Mixer Performance Charts Input IP3 vs RF Frequency Low-side Downconversion +17 dBm, 25° 250 MHz 150 MHz 350 MHz 28 26 1800 1900 2000 2100 2200 2300 RF Frequency (MHz) Conversion Loss vs RF Frequency Low-side Downconversion +17 dBm, 25°C 10 ...

Page 3

High Dynamic Range MMIC Mixer Performance Charts Input IP3 vs RF Frequency Low-side Downconversion +17 dBm, 25° 250 MHz 1800 1900 2000 2100 2200 RF Frequency (MHz) Input IP3 vs ...

Page 4

... High Dynamic Range MMIC Mixer Outline Drawing Land Pattern WJ Communications, Inc. • Phone: 1-800-WJ1-4401 • FAX: 408-577-6620 • e-mail: sales@wj.com • Web site: www.wj.com 'MH102' = Part Designation 'XXXX-X' = Lot Code Mounting Configuration Specifications and information are subject to change without notice. ...

Related keywords

mh102-pcb datasheet
mh102-pcb data sheet
mh102-pcb pdf datasheet
mh102-pcb component
mh102-pcb part
mh102-pcb distributor
mh102-pcb RoHS
mh102-pcb datasheet download