sp000278512 Infineon Technologies Corporation, sp000278512 Datasheet
sp000278512
Related parts for sp000278512
sp000278512 Summary of contents
Page 1
TLE4953C Differential Two-Wire Hall Effect Sensor Data Sheet, V 2.0, 2007-02 ...
Page 2
Edition 2007-02 Published by Infineon Technologies AG, 81726 München, Germany © Infineon Technologies AG 2/20/07. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms ...
Page 3
TLE4953 TLE4953C Revision History: Previous Version: Page Subjects (major changes since last revision) TLE4943 (without C) included We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will ...
Page 4
... Finally, the optimized piezo compensation and the integrated dynamic offset compensation enable easy manufacturing and elimination of magnetic offsets. Adaptive hysteresis concept increases the noise immunity. The TLE4953C is additionally provided with an overmolded 1.8 nF capacitor for improved EMI performance. Data Sheet Order Code Package SP000015141 PG-SSO-2-2 SP000278512 PG-SSO-2-1 1 TLE4953 TLE4953C PG-SSO-2-2 PG-SSO-2-1 V 2.0, 2007-02 ...
Page 5
Pin Configuration (top view) GyywwS 53C1R V GND CC Figure 1 supply generator Hall probes: R ight + - - D/A Centr (R+L)/2 Left - Figure 2 Block Diagram Data Sheet 2.5 2.67 Date Code 1.44 M arking ...
Page 6
Functional Description The differential Hall Effect IC detects the motion of ferromagnetic or permanent magnet structures by measuring the differential flux density of the magnetic field. To detect the motion of ferromagnetic objects the magnetic field must be provided by ...
Page 7
Figure 4 Definition of Rotation Direction Circuit Description The circuit internally is supplied by a voltage regulator MHz on-chip oscillator serves as a clock generator for the DSP and the output encoder. Speed signal circuitry TLE4953 speed signal ...
Page 8
After that consecutive output edges should have a nominal delay of about 360°. During the uncalibrated mode the offset value is calculated by the peak ...
Page 9
Vibration suppression algorithm: The magnetic signal amplitude and the direction information is used for detection of parasitic magnetic signals. Unwanted magnetic signals can be caused by angular or airgap vibrations for instance input signal is clearly detected as ...
Page 10
Absolute Maximum Ratings T = -40 to 155 °C, 4.0V ≤ Parameter Supply voltage Reverse polarity current Junction temperature Active lifetime Storage temperature Thermal resistance PG-SSO-2-2, PG-SSO-2-1 1) This allows together with an external serial resistor (75 or ...
Page 11
ESD Protection Human Body Model (HBM) tests according to: Standard EIA/JESD22-A114-B HBM (covers MIL STD 883D) Parameter ESD-Protection TLE4953C TLE4953 Operating Range Parameter Supply voltage Supply voltage Supply voltage ripple Junction temperature Pre-induction Pre-induction offset between outer probes Pre-induction offset ...
Page 12
AC/DC Characteristics All values specified at constant amplitude and offset of input signal, over operating range, unless otherwise specified. Typical values correspond to V Parameter Supply current Supply current Supply current ratio Output rise/fall slew rate TLE4953 Output rise/fall slew ...
Page 13
AC/DC Characteristics (cont’d) All values specified at constant amplitude and offset of input signal, over operating range, unless otherwise specified. Typical values correspond to V Parameter Systematic phase error of output edges during start-up and uncalibrated mode Phase shift during ...
Page 14
High 90% 50% 10% I Low Figure 5 Definition of Rise and Fall Time Timing Characteristics Parameter Pre-low length Speed signal Length of DR-L pulse Length of DR-R pulse Output of DR-L/R pulse, maximum frequency From ...
Page 15
Speed pulse occur only at the first pulse after start up or above If no magnetic differential signal change is detected the IC will remain in calibrated mode. No internal reset are generated - therefore a zero speed operation is ...
Page 16
Electro Magnetic Compatibility (values depend on Parameter Symbol Ref. ISO 7637-1; test circuit 1; B ∆ (amplitude of sinus signal); V Testpulse 1 EMC Testpulse 2 Testpulse 3a Testpulse 3b Testpulse 4 Testpulse 5 1) According to ...
Page 17
EMC-Generator V EMC Components: D1: 1N4007 Figure 7 Test Circuit 1 Figure 8 Package Outlines Data Sheet Mainframe D2: T 5Z27 µF/ nF/1000 ...
Page 18
PG-SSO-2-1 (Plastic Single Small Outline Package) 5.34 ±0.05 5.16 ±0.08 1.9 MAX. CODE 1.9 MAX. 2.54 6.35 ±0 solder function area Data Sheet 0.2 12.7 ± 45˚ ±1˚ CODE CODE 0.87 ±0.05 1.67 ±0.05 0.1 2x ...
Page 19
PG-SSO-2-2 (Plastic Single Small Outline Package) 5.34 ±0.05 5.16 ±0.08 B 1.9 MAX. CODE 2. 1.9 MAX. 0.2 B 5.16 ±0.08 6.35 ±0 (2.4) Capacitor (2.7) 5.34 ±0. solder function area Note: You ...
Page 20
Published by Infineon Technologies AG ...