hip0060 Intersil Corporation, hip0060 Datasheet

no-image

hip0060

Manufacturer Part Number
hip0060
Description
1.5a, 50v Quad Low Side Power Driver With Serial Bus Control And Fault Protection
Manufacturer
Intersil Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
hip0060AB
Manufacturer:
INTERSIL
Quantity:
1 188
Part Number:
hip0060AB
Manufacturer:
HARRIS
Quantity:
53
Part Number:
hip0060AB
Manufacturer:
INTERSIL
Quantity:
1 000
July 1997
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207
Features
• Quad NDMOS Output Drivers in a High Voltage Power
• Over-Stress Protection - Each Output
• Low Quiescent Current . . . . . . . . . . . . . . . . 10mA Max
• Serial Diagnostic Link with SPI Bus
• Diagnostic Interrupt Fault Flag
• 5V CMOS Logic Input Control
• Common Reset for Fault Bits and Output Drivers
• Ambient Operating
Applications
• Automotive and Industrial Systems
• Fuel Injection Drivers
• Solenoids, Relays and Lamp Drivers
• Logic and P Controlled Drivers
• Robotic Controls
Pinout
OUTB
OUTA
BiMOS Process
- Over-Current Limiting . . . . . . . . . . . . . . . . . .1.5A Min
- Internal Zener Drain-to-Gate Over-Voltage Clamp
- Thermal Shutdown Protection
- Open-Load Detection
Temperature Range. . . . . . . . . . . . . . . . -40
GND
GND
GND
GND
GND
INA
INB
INT
CS
Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50V Typ
SI
10
11
12
1
2
3
4
5
6
7
8
9
HIP0060 (SOIC)
TOP VIEW
24
23
22
21
20
19
18
17
16
15
14
13
|
V
RST
IND
OUTD
GND
GND
GND
GND
OUTC
INC
SO
SCK
Copyright
DD
©
Block Diagram
Intersil Corporation 1999
SCK
RST
V
INA
SO
CS
DD
SI
o
C to 125
CHANNEL A
(1 OF 4)
with Serial Bus Control and Fault Protection
+5V
8-BIT SPI
(SERIAL
DIAG.
REG)
o
C
B, C, D
1
+
1.5A, 50V Quad Low Side Power Driver
TO
Description
The HIP0060 is a 5V logic controlled Quad Low Side Power
Driver. The outputs are individually protected for over-current
(OC), over-temperature (OT) and over-voltage (OV). If an OC
short circuit in the output load is sensed (I
power driver, that output current will be independently limited
while the other outputs remain in operation. Over-current is
limited by direct gate feedback. Over-voltage protection is pro-
vided by a drain-to-gate zener diode that clamps inductive
switching pulses.
The output drivers are individually controlled through a Gate
Control Latch. Temperature is sensed at each output. If a ther-
mal fault exists, a status flag is set and the output is latched
off. Open-load (OL) and over-temperature (OT) faults sets a
status flag bit as diagnostic output to the SPI bus. For all fault
bits (8), an ORed one-shot interrupt signal is output to the INT
pin. An RST reset clears the fault flags and disables all out-
puts while active. The Serial Peripheral Interface (SPI) bus
pins are the Serial Input (SI), Serial Output (SO), Serial Data
Clock (SCK) and the Chip Select (CS).
The HIP0060 is fabricated in a Power BiMOS IC process, and
is intended for use in automotive and other applications having
a wide range of temperature and electrical stress conditions. It
is particularly suited for driving lamps, relays, and solenoids in
applications where low operating power, high breakdown volt-
age, and higher output current at high temperatures is required.
Ordering Information
HIP0060AB
CONTROL
PART NUMBER
LATCH
GATE
2
2
2
O.T.
BIT
FROM B, C, D
2
OPEN LOAD
DETECTOR
2
O.L.
RANGE (
BIT
-40 to 125
HIP0060
TEMP.
2
CURRENT
8 ORed O.T./O.L.
MULTI OUTPUT
FAULT INPUTS,
o
OVER
LIMIT
ONE-SHOT
C)
24 Ld SOIC
OVER TEMP.
DETECTOR
PACKAGE
I
S
File Number
S
) in one output
M24.3
INT
PKG.
OUTA
NO.
4045

Related parts for hip0060

hip0060 Summary of contents

Page 1

... Quad Low Side Power Driver with Serial Bus Control and Fault Protection Description The HIP0060 logic controlled Quad Low Side Power Driver. The outputs are individually protected for over-current (OC), over-temperature (OT) and over-voltage (OV short circuit in the output load is sensed (I power driver, that output current will be independently limited while the other outputs remain in operation ...

Page 2

... Low Output Voltage Input Pull-Down Current, INx I INPD Reset Input Pull-Up Current, RST I RPU HIP0060 Thermal Information Thermal Resistance (Typical, Notes SOIC - PC Board Mount, Min. Copper . . . . . . . . . . CL SOIC - PC Board Mount, 2 sq. in. Copper . . . . . . . . Maximum Storage Temperature Range -55 Maximum Lead Temperature (Soldering 10s 300 ...

Page 3

... Also, as shown in the Block Diagram, the OT fault status bit information is ORed into a one-shot that drives an open drain to provide an INT interrupt signal out- put. The INT output has a specified timing from the one-shot multi and is defined in the Electrical Specifications as t HIP0060 0V - 125 C ...

Page 4

... RST INA INB INC IND FIGURE 1. TYPICAL HIP0060 APPLICATION AS A LOW SIDE SWITCH FOR INDUCTIVE LOADS, LAMPS AND SMALL LINEAR MOTORS OR STEPPER MOTORS HIP0060 HIP0060 devices may be linked in cascade for the purposes of SPI control. Serial data is clocked in and out of each HIP0060 and then back to the host microcontroller. All linked devices have a common control sequence ...

Page 5

... REFER TO THE TIMING TEST CIRCUIT 10000 1000 100 10 0.1 FIGURE 3. MAXIMUM SINGLE PULSE ENERGY SAFE OPERATING AREA FOR EACH CLAMPED OUTPUT DRIVER, T HIP0060 V +5V DD 4.7k OUTA RST INA OUTB INB HIP0060 OUTC (TIMING TEST INC CIRCUIT) IND OUTD GND INT 90% 10% SAFE OPERATING AREA ...

Page 6

... SI xxxxxxxx SO (THREE-STATE) FIGURE 5. BYTE TIMING DIAGRAM WITH ASYNCHRONOUS RESET. REFER TO THE ELECTRICAL SPECIFICATION FOR THE HIGH AND LOW INPUT AND OUTPUT THRESHOLD LEVELS SHOWN FOR TIMING REFERENCE HIP0060 MSB INTERNAL STROBE FOR DATA CAPTURE FIGURE 4. DATA AND CLOCK TIMING DIAGRAM ...

Page 7

... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com HIP0060 M24.3 24 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE ...

Related keywords