SS8018TR SSC [Silicon Standard Corp.], SS8018TR Datasheet
SS8018TR
Related parts for SS8018TR
SS8018TR Summary of contents
Page 1
... LAN Servers Multi-Chip Modules Industrial Controllers n ORDERING INFORMATION SS8018XX PACKING TYPE TR: TAPE & REEL Example: SS8018TR à SS8018 shipped in tape & reel packing Rev.2.01 6/06/2003 with SMBus Serial Interface n DESCRIPTION The SS8018 is a precise digital thermometer that re- ports the temperature of both a remote sensor and its own package ...
Page 2
ABSOLUTE MAXIMUM RATINGS VCC to GND………….….………………………………………………..……….-0.3V to +6V DXP to GND……….……………………………………………………..……..…-0.3V to VCC + 0.3V DXN to GND………………………………………………….……..……………..-0.3V to +0.8V SMBCLK, SMBDATA, ALERT to GND……………………………………...…-0.3V to +6V SMBDATA, ALERT Current………………………………………………..…….-1mA to +50mA DXN Current………………………………………………..…..………………….±1mA ESD Protection (SMBCLK, SMBDATA, ALERT ...
Page 3
ELECTRICAL CHARACTERISTICS (cont.) (VCC = + 3.3V +85°C, unless otherwise noted.) A PARAMETER SMBus Interface Logic Input High Voltage Logic Input Low Voltage Logic Output Low Sink Current ALERT Output High Leakage Current Logic Input ...
Page 4
BLOCK DIAGRAM DXP DXP + + DXN DXN + + REMOTE TEMPERATURE REMOTE TEMPERATURE 11 11 DATA REGISTER DATA REGISTER HIGH-TEMPETATURE HIGH-TEMPETATURE 11 11 THRESHOLD (REMOTE THRESHOLD (REMOTE LOW-TEMPETATURE LOW-TEMPETATURE THRESHOLD (REMOTE THRESHOLD (REMOTE DIGITAL ...
Page 5
APPLICATIONS INFORMATION The SS8018 is a temperature sensor designed to work in conjunction with an external microcontroller (µC) or other intelligence in thermostatic, process-control or monitoring applications. The µC is typically a power- management or keyboard controller, generating SMBus ...
Page 6
ADC Noise Filtering The ADC is an integrating type with inherently good noise rejection. Micro-power operation places con- straints on high-frequency noise rejection; therefore, careful PC board layout and proper external noise filter- ing are required for high-accuracy remote measure- ...
Page 7
Low-Power Standby Mode Standby mode disables the ADC and reduces the sup- ply-current drain to about 10µA. Enter standby mode by forcing high to the /STOP bit in the configuration RUN byte register. Software standby mode behaves such that all ...
Page 8
Write Byte Format S ADDRESS WR 7 bits Slave Address: equivalent to chip- select line of a 3-wire interface Command Byte: selects which register you are writing to Data byte: data goes into the register set by the command byte ...
Page 9
Slave Address The SS8018 appears to the SMBus as one device hav- ing a common address for both ADC channels. The SS8018 device address is set to 1001100. The SS8018 also responds to the SMBus Alert Re- sponse slave address ...
Page 10
Command Byte Functions The 8-bit command byte register (Table 5) is the master index that points to the various other registers within the SS8018. The register’s POR state is 0000 0000, so that a Receive Byte transmission (a protocol that ...
Page 11
Table 6. Configuration-Byte Bit Assignments BIT NAME POR STATE 7 (MSB) MASK 0 / RUN 6 0 STOP 5-0 RFU 0 Table 7. Status-Byte Bit Assignments BIT NAME 7 (MSB) BUSY A high indicates that the ADC is busy converting. ...
Page 12
POR AND UVLO The SS8018 has a volatile memory. To prevent ambigu- ous power-supply conditions from corrupting the data in memory and causing erratic behavior, a POR voltage de- tector monitors VCC and clears the memory if VCC falls below ...
Page 13
HIGH LOW SMBCLK SMBDATA t t SU:STA HD:STA A = start condition B = MSB of address clocked into slave C = LSB of address clocked into slave D = R/W bit clocked into slave E ...
Page 14
PHYSICAL DIMENSIONS 8 Pin SOP Package ¢ X (4X Note: 1. Package body sizes exclude mold flash and gate burrs 2. Dimension L is measured in gage plane 3. Tolerance 0.10mm unless otherwise specified 4. Controlling dimension ...