DS26303L-XXX DALLAS [Dallas Semiconductor], DS26303L-XXX Datasheet - Page 65
DS26303L-XXX
Manufacturer Part Number
DS26303L-XXX
Description
3.3V, E1/T1/J1, Short-Haul, Octal Line Interface Unit
Manufacturer
DALLAS [Dallas Semiconductor]
Datasheet
1.DS26303L-XXX.pdf
(101 pages)
- Current page: 65 of 101
- Download datasheet (2Mb)
6.7 G.772 Monitor
In this application, only seven LIUs are functional and one LIU is used for nonintrusive monitoring of input and
output of the other seven channels. Channel 1 is used for monitoring channels 2 to 8. G.772 monitoring is
configured by the
remote loopback and the monitored signal can be output on TTIP1 and TRING1.
6.8 Loopbacks
The DS26303 provides four loopbacks for diagnostic purposes: analog loopback (ALBC:ALBCn set), digital
loopback (DLBC:DLBCn set), remote loopback (RLBC:RLBCn set), and dual loopback (DLBC:DLBCn set and
(RLBC:RLBCn set).
6.8.1
The analog output of the transmitter TTIPn and TRINGn is looped back to RTIPn and RRINGn of the receiver. Data
at RTIPn and RRINGn is ignored in analog loopback. See
Figure 6-8. Analog Loopback
6.8.2
The transmit system data TPOSn, TNEGn, and TCLKn are looped back to output on RCLKn, RPOSn, and RNEGn.
The data input at TPOSn and TNEGn is encoded and output on TTIPn and TRINGn. Signals at RTIPn and
RRINGn are ignored. This loopback is conceptually shown in
TCLK
TNEG
TPOS
Analog Loopback
Digital Loopback
RNEG
RPOS
RCLK
H D B 3 /
B 8 Z S
D e c o d e r
GMC
H D B 3 /
B 8 Z S
E n c o d e r
register (see
Table
O p t i o n a l
J i t t e r
A t t e n u a t o r
O p t i o n a l
J i t t e r
A t t e n u a t o r
5-9). While monitoring with channel 1, the device can be configured in
DS26303: 3.3V, T1/E1/J1, Short-Haul, Octal Line Interface Unit
65 of 101
Figure
T r a n s m i t
D i g i t a l
R e c e i v e
D i g i t a l
Figure
6-8.
6-9.
T r a n s m i t
A n a l o g
R e c e i v e
A n a l o g
Line
Driver
Rtip
Rring
Related parts for DS26303L-XXX
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
TYPE DS FUSED DISCONNECT SWITCH 60A 3P
Manufacturer:
EATON CUTLER HAMMER
Part Number:
Description:
High Resolution Temperature Measurement with Dallas Direct-to-Digital Temperature Sensors
Manufacturer:
Dallas Semiconductor
Part Number:
Description:
32.768kHz Temperature-Compensated Crystal Oscillator
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
3.3 volt micromonitor, tolerance 20%
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
Ultra3 LVD/SE SCSI Terminator
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
SCSI Terminator
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
5-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
Afterburner Chip
Manufacturer:
Dallas Semiconductor
Datasheet:
Part Number:
Description:
10-Tap Silicon Delay Line
Manufacturer:
Dallas Semiconductor
Datasheet: