SC16C654BIB64 PHILIPS [NXP Semiconductors], SC16C654BIB64 Datasheet - Page 22

• Manufacturer Part Number: SC16C654BIB64
• Description: 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
• Manufacturer: PHILIPS [NXP Semiconductors]

Philips Semiconductors
9397 750 14965
Product data sheet
6.10 DMA operation
6.11 Sleep mode
6.12 Loop-back mode
The SC16C654B/654DB FIFO trigger level provides additional flexibility to the user for
block mode operation. LSR[5:6] provide an indication when the transmitter is empty or has
an empty location(s). The user can optionally operate the transmit and receive FIFOs in
the DMA mode (FCR[3]). When the transmit and receive FIFOs are enabled and the DMA
mode is de-activated (DMA Mode 0), the SC16C654B/654DB activates the interrupt
output pin for each data transmit or receive operation. When DMA mode is activated
(DMA Mode 1), the user takes the advantage of block mode operation by loading or
unloading the FIFO in a block sequence determined by the preset trigger level. In this
mode, the SC16C654B/654DB sets the interrupt output pin when characters in the
transmit FIFOs are below the transmit trigger level, or the characters in the receive FIFOs
are above the receive trigger level.
Remark: DMA operation is not supported in the HVQFN48 package option.
The SC16C654B/654DB is designed to operate with low power consumption. A special
sleep mode is included to further reduce power consumption when the chip is not being
used. With EFR[4] and IER[4] enabled (set to a logic 1), the SC16C654B/654DB enters
the sleep mode, but resumes normal operation when a start bit is detected, a change of
state on any of the modem input pins RX, RI, CTS, DSR, CD, or a transmit data is
provided by the user. If the sleep mode is enabled and the SC16C654B/654DB is
awakened by one of the conditions described above, it will return to the sleep mode
automatically after the last character is transmitted or read by the user. In any case, the
sleep mode will not be entered while an interrupt(s) is pending. The SC16C654B/654DB
will stay in the sleep mode of operation until it is disabled by setting IER[4] to a logic 0.
The internal loop-back capability allows on-board diagnostics. In the loop-back mode, the
normal modem interface pins are disconnected and reconfigured for loop-back internally.
MCR[0:3] register bits are used for controlling loop-back diagnostic testing. In the
loop-back mode, OP1 and OP2 in the MCR register (bits 2:3) control the modem RI and
CD inputs, respectively. MCR signals DTR and RTS (bits 0:1) are used to control the
modem DSR and CTS inputs, respectively. The transmitter output (TX) and the receiver
input (RX) are disconnected from their associated interface pins, and instead are
connected together internally; see
disconnected from their normal modem control input pins, and instead are connected
internally to RTS, DTR, OP2 and OP1. Loop-back test data is entered into the transmit
holding register via the user data bus interface, D[0:7]. The transmit UART serializes the
data and passes the serial data to the receive UART via the internal loop-back connection.
The receive UART converts the serial data back into parallel data that is then made
available at the user data interface D[0:7]. The user optionally compares the received data
to the initial transmitted data for verifying error-free operation of the UART TX/RX circuits.
In this mode, the receiver and transmitter interrupts are fully operational. The Modem
Control Interrupts are also operational. However, the interrupts can only be read using
lower four bits of the Modem Status Register (MSR[0:3]) instead of the four Modem Status
Register bits 4:7. The interrupts are still controlled by the IER.
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
Rev. 02 — 20 June 2005
Figure
12. The CTS, DSR, CD, and RI are
SC16C654B/654DB
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
22 of 58