LSI53C875 LSI Logic, LSI53C875 Datasheet - Page 44
LSI53C875
Manufacturer Part Number
LSI53C875
Description
PCI to Ultra SCSI I/O Processor
Manufacturer
LSI Logic
Datasheet
1.LSI53C875.pdf
(314 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LSI53C875-160QFP
Manufacturer:
LSI
Quantity:
20 000
Company:
Part Number:
LSI53C875J
Manufacturer:
NS
Quantity:
4 490
Part Number:
LSI53C875J
Manufacturer:
LSILOGIC
Quantity:
20 000
- Current page: 44 of 314
- Download datasheet (3Mb)
2.5.9.1 Differential Mode
Table 2.5
2-20
Signal
BSYDIR, SELDIR,
RSTDIR
SDIR[15:0],
SDIRP[1:0]
IGS
TGS
DIFFSENS
Differential Mode
Function
Active HIGH signals used to enable the differential drivers as outputs for SCSI
signals BSY/, SEL/, and RST/, respectively.
Active HIGH signals used to control direction of the differential drivers for SCSI
data and parity lines, respectively.
Active HIGH signal used to control direction of the differential driver for initiator
group signals ATN/ and ACK/.
Active HIGH signal used to control direction of the differential drivers for target
group signals MSG/, C/D/, I/O/, and REQ/.
Input to the LSI53C875 used to detect the presence of a SE device on a
differential system. If a logical zero is detected on this pin, then it is assumed
that an SE device is on the bus and all SCSI outputs will be 3-stated to avoid
damage to the transceiver.
In differential mode, the SDIR[15:0], SDIRP[1:0], IGS, TGS, RSTDIR,
BSYDIR, and SELDIR signals control the direction of external differential
pair transceivers. The LSI53C875 is placed in differential mode by setting
the DIF bit, bit 5 of the
this bit 3-states the BSY/, SEL/, and RST/ pads so they can be used as
pure input pins. In addition to the standard SCSI lines, the following
signals defined in
LSI53C875:
See
LSI53C875 is connected to the Texas Instruments SN75976A differential
transceiver. The recommended value of the pull-up resistor on the REQ/,
ACK/, MSG/, C/D/, I/O/, ATN/, SD[7:0]/, and SDP0/ lines is 680
the Active Negation portion of TolerANT technology is not enabled.
When Active Negation is enabled, the recommended resistor value on
the REQ/, ACK/, SD[7:0]/, and SDP0/ signals is 1.5 k . The electrical
characteristics of these pins change when Active Negation is enabled,
permitting a higher resistor value.
Functional Description
Figure 2.3
for an example differential wiring diagram, in which the
Table 2.5
SCSI Test Two (STEST2)
are used during differential operation by the
register (0x4E). Setting
when
Related parts for LSI53C875
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
LR33000 Self-Embedding Processor
Manufacturer:
LSI [LSI Computer Systems]
Datasheet:
Part Number:
Description:
LSI for 16 CH Multiplexing
Manufacturer:
Mitsubishi
Datasheet:
Part Number:
Description:
DVD Recorder System Processor
Manufacturer:
LSI Logic
Datasheet:
Part Number:
Description:
DVD Recorder System Processor
Manufacturer:
LSI Logic
Datasheet:
Part Number:
Description:
Servo / Video Decoder and System Processor
Manufacturer:
LSI Logic
Datasheet:
Part Number:
Description:
Mpeg-2 Audio/video Decoder
Manufacturer:
LSI Logic Corporation
Datasheet:
Part Number:
Description:
Satellite Decoder Technical Manual 5/97
Manufacturer:
LSI Logic Corporation
Datasheet:
Part Number:
Description:
Satellite Receiver
Manufacturer:
LSI Logic Corporation
Datasheet: