DAC10 Analog Devices, DAC10 Datasheet
DAC10
Available stocks
Related parts for DAC10
DAC10 Summary of contents
Page 1
... Zener diodes, to provide 1/2 LSB full-scale accuracy without the need for laser trimming. Single-chip reliability, coupled with low cost and outstanding flexibility, make the DAC10 device an ideal building block for A/D converters, Data Acquisition systems, CRT displays, pro- grammable test equipment and other applications where low power consumption, input/output versatility and long-term stability are required ...
Page 2
... S REF apply to both I and I .) OUT OUT Min 10 Full-Scale Current Change, <1 LSB – 10.000 V, REF R14 = R15 = 5.000 k 3.978 I – –2– +70 C for DAC10F and G, unless otherwise noted. A and I .) OUT OUT DAC10F DAC10G Typ Max Min Typ Max 10 0.3 0.5 0.6 1 0.3 1 0.7 85 ...
Page 3
... DAC10N Limit 10 10 0.5 +10 –5 18 0.5 2 0.8 4 – mA, unless otherwise noted. Output characteristics and I ). OUT DAC10F Typ DAC10 Units Bits min Bits min LSB max V max V min A max A max V min V max mA max mA max Units ns ppm FS ...
Page 4
... DAC10 ABSOLUTE MAXIMUM RATINGS Operating Temperature DAC10FX, GX, GS +70 C Junction Temperature ( – +150 C J Storage Temperature . . . . . . . . . . . . . . . . . . – +150 C Lead Temperature (Soldering, 60 sec +300 C V+ Supply to V– Supply . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Logic Inputs . . . . . . . . . . . . . . . . . . . . . . V– to V– plus V– Analog Current Outputs . . . . . . . . . . . . . . . . + – ...
Page 5
... F 0.01 F V– V+ Figure 7. Basic Positive Reference Operation CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. REV. D Typical Performance Characteristics–DAC10 8 MIN MAX 7.2 ALL BITS ON 6 ...
Page 6
... REF (+) DAC10 2.000mA 5k +15V MSB 5.000 DAC10 5k REF01 C GND 4 V+ V– R17 IS FOR BIAS FS Figure 10. Recommended Full-Scale Adjustment Circuit B B LSB 1 B FULL RANGE HALF-SCALE +LSB ...
Page 7
... Figure 17. Interfacing with Various Logic Families –7– 0.001V 0.001V +15V 0 0.01 F 4.7 F 2N918 V O 499k 1/4W, 5% CARBON –15V 1/2 LSB SETTLING = 7.8mV +15V TTL +1.4V +15V CMOS +7.6V TH 9.1k DAC10 V LC 6.2k 0 ECL 13k 2N3904 "A" 2N3904 3k TO PIN 1 39k V LC 6.2k –5.2V DAC10 175mV +1. ...
Page 8
... For V– = – the logic inputs may swing between –5 and +18 V. This enables REF direct interface with +15 V CMOS logic, even when the DAC10 plus powered from supply. Minimum input logic swing and REF minimum logic threshold voltage are given by: V– ...
Page 9
... CRT deflection and in other balanced applications such as driving center-tapped coils and transformers. POWER SUPPLIES The DAC10 operates over a wide range of power supply volt- ages from a total supply When operating with V– supplies of – less recommended. Low ...
Page 10
... DAC10 0.200 (5.08) 0.200 (5.08) 0.125 (3.18) 0.210 (5.33) 0.160 (4.06) 0.115 (2.93) 0.2992 (7.60) 0.2914 (7.40) 0.0118 (0.30) 0.0040 (0.10) OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 18-Lead Cerdip (Q-18) 0.005 (0.13) MIN 0.098 (2.49) MAX 18 10 0.310 (7.87) 0.220 (5.59 PIN 1 0.060 (1.52) 0.960 (24.38) MAX 0.015 (0.38) MAX 0.150 (3.81) MIN 0.023 (0.58) 0.100 SEATING 0.070 (1.78) 15 (2.54) PLANE 0.014 (0.36) ...