MC68HC08AZ60ACFU MOTOROLA [Motorola, Inc], MC68HC08AZ60ACFU Datasheet - Page 257
MC68HC08AZ60ACFU
Manufacturer Part Number
MC68HC08AZ60ACFU
Description
Microcontrollers
Manufacturer
MOTOROLA [Motorola, Inc]
Datasheet
1.MC68HC08AZ60ACFU.pdf
(480 pages)
- Current page: 257 of 480
- Download datasheet (3Mb)
17.6.2 Transmission Format When CPHA = ‘0’
MC68HC08AZ60A — Rev 0.0
MOTOROLA
NOTE:
The clock phase (CPHA) control bit selects one of two fundamentally
different transmission formats. The clock phase and polarity should be
identical for the master SPI device and the communicating slave device.
In some cases, the phase and polarity are changed between
transmissions to allow a master device to communicate with peripheral
slaves having different requirements.
Before writing to the CPOL bit or the CPHA bit, the SPI should be
disabled by clearing the SPI enable bit (SPE).
Figure 17-4
should not be used as a replacement for data sheet parametric
information.Two waveforms are shown for SCK: one for CPOL = ‘0’ and
another for CPOL = ‘1’. The diagram may be interpreted as a master or
slave timing diagram since the serial clock (SCK), master in/slave out
(MISO), and master out/slave in (MOSI) pins are directly connected
between the master and the slave. The MISO signal is the output from
the slave, and the MOSI signal is the output from the master. The SS line
is the slave select input to the slave. The slave SPI drives its MISO
output only when its slave select input (SS) is at logic ‘0’, so that only the
selected slave drives to the master. The SS pin of the master is not
shown but is assumed to be inactive. The SS pin of the master must be
high or must be reconfigured as general purpose I/O not affecting the
SPI. See Mode Fault Error. When CPHA = ‘0’, the first SPSCK edge is
the MSB capture strobe. Therefore the slave must begin driving its data
before the first SPSCK edge, and a falling edge on the SS pin is used to
start the transmission. The SS pin must be toggled high and then low
again between each byte transmitted.
Serial Peripheral Interface (SPI)
shows an SPI transmission in which CPHA is ‘0’. The figure
Serial Peripheral Interface (SPI)
Transmission Formats
Advance Information
257
Related parts for MC68HC08AZ60ACFU
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Motorola, Inc [VOLTAGE REGULATOR]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
6367254 MOTOROLA SC (XSTRS/R F)
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
MC1494LMotorola, Inc [MONOLITHIC FOUR-QUADRANT MULTIPLIER]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
MC1466LMotorola, Inc [PRECISION WIDE RANGE VOLTAGE AND CURRENT REGULATOR]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
MC145532DWMotorola, Inc [ADPCM Transcoder]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Silicon Controlled Rectifiers
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF Power Field Effect Transistors N-Channel Enhancement-Mode Lateral MOSFETs
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF POWER FIELD EFFECT TRANSISTORS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
LATERAL N-CHANNEL BROADBAND RF POWER MOSFETs
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF POWER FIELD EFFECT TRANSISTOR
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF LOW POWER TRANSISTOR NPN SILICON
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
PLASTIC SURFACE MOUNT ZENER DIODES 1.5 WATTS 3.3-68 VOLTS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
OVERVOLTAGE TRANSIENT SUPPRESSOR
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
TMOS POWER FET 15 AMPERES 60 VOLTS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
TMOS POWER FET LOGIC LEVEL 19 AMPERES 30 VOLTS RDS(on) = 0.099 OHM
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet: