FDC37B787QF SMSC [SMSC Corporation], FDC37B787QF Datasheet - Page 76
FDC37B787QF
Manufacturer Part Number
FDC37B787QF
Description
Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
Manufacturer
SMSC [SMSC Corporation]
Datasheet
1.FDC37B787QF.pdf
(249 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 76 of 249
- Download datasheet (881Kb)
6.
Bit 1
This bit controls the Request To Send (nRTS)
output. Bit 1 affects the nRTS output in a manner
identical to that described above for bit 0.
Bit 2
This bit controls the Output 1 (OUT1) bit. This bit
does not have an output pin and can only be read
or written by the CPU.
Bit 3
Output 2 (OUT2). This bit is used to enable an
UART interrupt. When OUT2 is a logic "0", the
serial port interrupt output is forced to a high
impedance state - disabled.
logic "1", the serial port interrupt outputs are
enabled.
Bit 4
This bit provides the loopback feature for
diagnostic testing of the Serial Port. When bit 4 is
set to logic "1", the following occur:
1. The TXD is set to the Marking State(logic "1").
2. The
3. The output of the Transmitter Shift Register is
4. All MODEM Control inputs (nCTS, nDSR, nRI
5. The four MODEM Control outputs (nDTR,
7. Data that is transmitted is immediately
This feature allows the processor to verify the
transmit and receive data paths of the Serial Port.
In the diagnostic mode, the receiver and the
transmitter interrupts are fully operational. The
MODEM Control Interrupts are also operational
but the interrupts' sources are now the lower four
bits of the MODEM Control Register instead of the
MODEM Control inputs. The interrupts are still
controlled by the Interrupt Enable Register.
Bits 5 through 7
These bits are permanently set to logic zero.
disconnected.
"looped back" into the Receiver Shift Register
input.
and nDCD) are disconnected.
nRTS, OUT1 and OUT2) are internally
connected to the four MODEM Control inputs
(nDSR, nCTS, RI, DCD).
received.
The Modem Control output pins are forced
inactive high.
receiver
Serial
Input
When OUT2 is a
(RXD)
is
77
LINE STATUS REGISTER (LSR)
Address Offset = 5H, DLAB = X, READ/WRITE
Bit 0
Data Ready (DR). It is set to a logic "1" whenever
a complete incoming character has been received
and transferred into the Receiver Buffer Register
or the FIFO. Bit 0 is reset to a logic "0" by reading
all of the data in the Receive Buffer Register or the
FIFO.
Bit 1
Overrun Error (OE). Bit 1 indicates that data in the
Receiver Buffer Register was not read before the
next character was transferred into the register,
thereby destroying the previous character.
FIFO mode, an overrunn error will occur only when
the FIFO is full and the next character has been
completely received in the shift register, the
character in the shift register is overwritten but not
transferred to the FIFO. The OE indicator is set to
a logic "1" immediately upon detection of an
overrun condition, and reset whenever the Line
Status Register is read.
Bit 2
Parity Error (PE). Bit 2 indicates that the received
data character does not have the correct even or
odd parity, as selected by the even parity select
bit. The PE is set to a logic "1" upon detection of a
parity error and is reset to a logic "0" whenever the
Line Status Register is read. In the FIFO mode
this error is associated with the particular character
in the FIFO it applies to. This error is indicated
when the associated character is at the top of the
FIFO.
Bit 3
Framing Error (FE).
received character did not have a valid stop bit.
Bit 3 is set to a logic "1" whenever the stop bit
following the last data bit or parity bit is detected
as a zero bit (Spacing level). The FE is reset to a
logic "0" whenever the Line Status Register is
read. In the FIFO mode this error is associated
with the particular character in the FIFO it applies
to. This error is indicated when the associated
character is at the top of the FIFO. The Serial Port
will try to resynchronize after a framing error. To
do this, it assumes that the framing error was due
to the next start bit, so it samples this 'start' bit
twice and then takes in the 'data'.
Bit 4
Bit 3 indicates that the
In
Related parts for FDC37B787QF
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: