SAB-C167CR-4R33M INFINEON [Infineon Technologies AG], SAB-C167CR-4R33M Datasheet - Page 63

• Manufacturer Part Number: SAB-C167CR-4R33M
• Description: 16-Bit Single-Chip Microcontroller
• Manufacturer: INFINEON [Infineon Technologies AG]

Table 11
Parameter
Output high voltage
(PORT0, PORT1, Port 4, ALE,
RD, WR, BHE, CLKOUT,
RSTOUT)
Output high voltage
(all other outputs)
Input leakage current (Port 5)
Input leakage current
(all other)
RSTIN inactive current
RSTIN active current
READY/RD/WR inact. current
READY/RD/WR active current
ALE inactive current
ALE active current
Port 6 inactive current
Port 6 active current
PORT0 configuration current
XTAL1 input current
Pin capacitance
(digital inputs/outputs)
1) Keeping signal levels within the levels specified in this table, ensures operation without overload conditions.
2) Valid in bidirectional reset mode only.
3) This specification is not valid for outputs which are switched to open drain mode. In this case the respective
4) This parameter is not valid for pins READY, ALE, RD, and WR while the respective pull device is on.
5) These parameters describe the RSTIN pull-up, which equals a resistance of ca. 50 to 250 kΩ.
6) The maximum current may be drawn while the respective signal line remains inactive.
7) The minimum current must be drawn in order to drive the respective signal line active.
8) This specification is valid during Reset and during Hold-mode or Adapt-mode. During Hold-mode Port 6 pins
Data Sheet
For signal levels outside these specifications also refer to the specification of the overload current
output will float and the voltage results from the external circuitry.
are only affected, if they are used (configured) for CS output and the open drain function is not enabled. The
READY-pull-up is always active, except for Power-down mode.
4)
DC Characteristics (Operating Conditions apply)
10)
8)
3)
3)
8)
8)
5)
8)
5)
9)
8)
8)
Symbol
V
V
I
I
I
I
I
I
I
I
I
I
I
I
I
C
OZ1
OZ2
RSTH
RSTL
RWH
RWL
ALEL
ALEH
P6H
P6L
P0H
P0L
IL
OH
OH1
IO
7)
7)
6)
6)
7)
6)
6)
7)
7)
6)
CC 2.4
CC 2.4
CC –
CC –
CC –
CC –
61
Min.
0.9
0.9
–
-100
–
-500
–
500
–
-500
–
-100
Limit Values
V
V
DD
DD
Max.
–
–
–
–
±200
±500
-10
–
-40
–
40
–
-40
–
-10
–
±20
10
Unit Test Condition
V
V
V
V
nA
nA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
pF
1)
Electrical Parameters
(cont’d)
I
I
I
I
0 V <
0.45 V <
V
V
V
V
V
V
V
V
V
V
V
0 V <
f
T
OH
OH
OH
OH
= 1 MHz;
A
DD
IN
IN
OUT
OUT
OUT
OUT
OUT
OUT
IN
IN
= 25 °C
=
=
=
=
= -2.4 mA
= -0.5 mA
= -1.6 mA
= -0.5 mA
V3.3, 2005-02
= 2.4 V
=
=
= 2.4 V
= 2.4 V
=
V
V
V
V
V
V
IH1
IL
IHmin
ILmax
V
V
V
IN
IN
C167CR
C167SR
OLmax
OLmax
OL1max
V
<
I
<
OV
IN
V
V
.
<
DD
DD