HCPL-1930-100 HP [Agilent(Hewlett-Packard)], HCPL-1930-100 Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
HCPL-1930-100
Manufacturer Part Number
HCPL-1930-100
Description
Dual Channel Line Receiver Dual Channel Line Receiver Dual Channel Line Receiver
Manufacturer
HP [Agilent(Hewlett-Packard)]
Datasheet
1.HCPL-1930-100.pdf
(12 pages)
Typical Specifications
T
Notes:
10. CM
11. Measured between adjacent input leads shorted together, i.e. between 1, 2 and 4 shorted together and pins 5, 6 and 8 shorted
12. No external pull up is required for a high logic state on the enable input.
13. Measured between pins 1 and 2 or 5 and 6 shorted together, and pins 10 through 15 shorted together.
14. Parameters shall be tested as part of device initial characterization and after process changes. Parameters shall be guaranteed to the
15. Standard parts receive 100% testing at 25 C (Subgroups 1 and 9). Hi-Rel and SMD parts receive 100% testing at 25, 125, and -55 C
1. Bypassing of the power supply line is required, with a 0.1 F ceramic disc capacitor adjacent to each isolator. The power supply bus
2. Derate linearly at 1.2 mA/ C above T
3. Each channel.
4. Device considered a two terminal device: pins 1 through 8 are shorted together, and pins 9 through 16 are shorted together.
5. The t
6. The t
7. The t
8. The t
9. CM
A
Resistance (Input-Output)
Capacitance (Input-Output)
Input-Input Insulation
Leakage Current
Resistance (Input-Input)
Capacitance (Input-Input)
Propagation Delay Time of Enable
from V
Propagation Delay Time of Enable
from V
Output Rise Time (10-90%)
Output Fall Time (90-10%)
Input Capacitance
= 25 C, V
for the isolators should be separate from the bus for any active loads, otherwise additional bypass capacitance may be needed to
suppress regenerative feedback via the power supply.
edge of the output pulse.
edge of the output pulse.
on the trailing edge of the output pulse.
on the leading edge of the output pulse.
V
V
together.
limits specified for all lots not specifically tested.
(Subgroups 1 and 9, 2 and 10, 3 and 11, respectively).
OUT
OUT
H
L
> 2.0 V.
< 0.8 V.
is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a high logic state, i.e.
is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state, i.e.
EH
EL
PLH
PHL
ELH
EHL
to V
to V
Parameter
propagation delay is measured form the 6.5 mA point on the trailing edge of the input pulse to the 1.5 V point on the trailing
propagation delay is measured from the 6.5 mA point on the leading edge of the input pulse to the 1.5 V point on the leading
enable propagation delay is measured from the 1.5 V point on the trailing edge of the enable input pulse to the 1.5 V point
enable propagation delay is measured from the 1.5 V point on the leading edge of the enable input pulse to the 1.5 V point
EH
EL
CC
= 5 V
A
= 100 C.
Symbol
R
C
t
t
R
C
I
ELH
EHL
C
t
t
I-I
I-O
I-O
I-I
I-I
r
f
I
Typ.
0.55
10
10
1.7
0.5
35
35
30
24
60
12
12
Units
pF
nA
pF
pF
ns
ns
ns
ns
V
f = 1 MHz
45% Relative Humidity,
V
V
f = 1 MHz
R
I
R
f = 1 MHz, V
PINS 1 to 2 or 5 to 6
I
I-O
I-I
I-I
L
L
= 13 mA, V
= 510 , C
= 510 , C
= 500 Vdc, t = 5 s
= 500 Vdc
= 500 V dc
Test Conditions
EH
I
L
L
= 0,
7
= 15 pF,
= 3 V, V
= 15 pF, I
EL
I
= 0 V
= 13 mA
Fig.
6, 7
6, 7
Note
3, 13
3, 13
3, 7
3, 8
11
11
11
3
3
3