HD6475328-CP10 HITACHI [Hitachi Semiconductor], HD6475328-CP10 Datasheet - Page 112
HD6475328-CP10
Manufacturer Part Number
HD6475328-CP10
Description
original Hitachi CMOS microcomputer unit (MCU)
Manufacturer
HITACHI [Hitachi Semiconductor]
Datasheet
1.HD6475328-CP10.pdf
(459 pages)
- Current page: 112 of 459
- Download datasheet (998Kb)
currently executing one of the five instructions listed above. After executing this instruction the
CPU always proceeds to the next instruction. (And if the next instruction is one of these five, the
CPU also proceeds to the next instruction after that.) The exception-handling sequence starts after
the next instruction that is not one of these five has been executed. The following is an example:
(Example)
LDC.B #H'00,TP
MOV.W #H'FF80,SP
MOV.B #H'00,@WCR
4.8.2 Disabling of Exceptions Immediately after a Reset
If an interrupt is accepted after a reset and before the stack pointer (SP) is initialized, the program
counter and status register will not be saved correctly, leading to a program crash. To prevent this,
when the chip comes out of the reset state all interrupts, including the NMI, are disabled, so the
first instruction of the reset routine is always executed. As noted earlier, in the minimum mode,
this instruction should initialize the stack pointer (SP). In the maximum mode, the first instruction
should be an LDC instruction that initializes the stack page register (TP); the next instruction
should initialize the stack pointer.
4.8.3 Disabling of Interrupts after a Data Transfer Cycle
If an interrupt starts the data transfer controller and another interrupt is requested during the data
transfer cycle, when the data transfer cycle ends, the CPU always executes the next instruction
before handling the second interrupt.
Even if a nonmaskable interrupt (NMI) occurs during a data transfer cycle, it is not accepted until
the next instruction has been executed. An example of this is shown below.
.
.
.
.
.
.
.
.
.
Program flow
Interrupt controller notifies CPU
of interrupt request
CPU executes the instruction next to LDC before
starting exception handling
93
To exception-handling sequence
Related parts for HD6475328-CP10
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Silicon N-Channel MOS FET
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet:
Part Number:
Description:
LOW FREQUENCY POWER AMPLIFIER
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet:
Part Number:
Description:
Silicon N-Channel MOS FET
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet:
Part Number:
Description:
Silicon N-Channel MOS FET
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet:
Part Number:
Description:
Silicon N-Channel MOS FET
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet:
Part Number:
Description:
Silicon N-Channel MOS FET
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet:
Part Number:
Description:
SILICON N-CHANNEL JUNCTION FET LOW FREQUECY LOW NOISE AMPLIFIER
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet:
Part Number:
Description:
Silicon P-Channel MOS FET
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet:
Part Number:
Description:
Silicon P-Channel MOS FET
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet:
Part Number:
Description:
SILICON SPEED POWER SWITCHING
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet:
Part Number:
Description:
SILICON P-CHANNEL MOS FET HIGH SPEED POWER SWITCHING
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet:
Part Number:
Description:
SILICON P-CHANNEL MOS FET
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet:
Part Number:
Description:
SILICON P-CHANNEL MOS FET
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet:
Part Number:
Description:
Silicon P-Channel MOS FET
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet:
Part Number:
Description:
Silicon P-Channel MOS FET
Manufacturer:
HITACHI [Hitachi Semiconductor]
Datasheet: