IRPT1059C IRF [International Rectifier], IRPT1059C Datasheet
IRPT1059C
Related parts for IRPT1059C
IRPT1059C Summary of contents
Page 1
... DC bus voltage and current feedback · Protection for short-circuit, earth/ground fault and overtemperature · Terminal blocks for single-phase input and output connections PRELIMINARY 180 - 240V single-phase input Figure 1. The IRPT1059C 6.103 IRPT1059 IRPT1059C within a motor control system page 1 ...
Page 2
... PWM controller for inverter IGBT switching. The power supply offers the user non-isolated 5V and 15V to power the micro-controller. The IRPT1059C offers several benefits to the drive manufacturer listed below: • It greatly simplifies component selection, design of layout, interconnection, gate drive, local power supply, thermal sensing, current sensing and protection ...
Page 3
The IRPT1059D Driver- Plus Board The IRPT1059D Driver-Plus board, shown in figure 3, houses surge suppression MOV on input, a switching power supply bus filter capacitor with NTC inrush current limiter, an IR2132J monolithic 3-phase driver IC, and ...
Page 4
... IRPT1059 page 4 Figure 4. IRPT1059C Basic Architecture www.irf.com ...
Page 5
Specifications PARAMETERS Input Power Voltage Frequency Input current Output Power Voltage Nominal Motor hp (kW) Nominal motor current Control Inputs PWM input signals IN1...IN6 Pulse deadtime Minimum input pulse width RESET Protection Output current trip level Earth/gnd fault current trip ...
Page 6
IRPT1059 Power 100% PWM Frequency (kHz) – (Induction Motor Load) Figure 5a. 1hp/4.4A Output Heat sink Thermal Resistance and Power Dissipation vs. PWM Frequency Power 150% Power 100% Figure 5b. 0.75hp/3.5A Output Heat Sink Thermal Resistance and Power Dissipation vs. ...
Page 7
... U,V and W (J2). Power-Up Procedure When single-phase input power is first switched on, PWM inputs to the IRPT1059C must be inhibited (held high) until the protection latch circuitry is reset. To reset this latch before inverter start-up, RESET pin on J3 connector must be pulled down low for at least 2 sec. This will set the Fault feedback signal on J3 high ...
Page 8
IRPT1059 IRPT1059D Mechanical Specifications NOTE: Dimensions are in inches [milliimeters] 1.5625 (39.6875) 2.625 (66.675) page 8 4.125 (104.775) 2.25 (57.15) PCB 1.500 (38.100) Capacitor Module Heatsink Figure ...
Page 9
IRPT1059A Mechanical Specifications NOTE: Dimensions are in inches [milliimeters] .875 [22.27] PIN CENTER .000 [0.00] PIN CENTER .875 .[22.27] 28X [ .026 – .024)] 28X .040 [1.02] www.irf.com ALL PIN COORDINATE DIMENSIONS ARE BASIC PIN DIAGONAL .037 – .034 [.940 ...
Page 10
... MOVs, IGBT gate drivers, protection circuitry and low power supply. The PCB is functionally tested with standard power module to meet all system specifications. IRPT1059E Design Kit Complete (IRPT1059C) with full set of design documentation including schematic diagram, bill of material, mechanical layout, schematic files, Gerber files and design tips. www.irf.com ...
Page 11
CAUTION: All control logic is referenced to negative power bus which is live with respect to earth/ground. Capacitor Soft Charge DC bus capacitors are connected to the rectifier bridge output through an NTC. At power-up, the NTC limits the inrush ...
Page 12
IRPT1059 bus current, 0.045V/A nominal. This pin must not be FB connected to circuit ground (N) through low impedance. If filtering of this signal is required, it shoud be done by adding a high impedance buffer stage ...