HPCL7800 HP [Agilent(Hewlett-Packard)], HPCL7800 Datasheet
HPCL7800
Related parts for HPCL7800
HPCL7800 Summary of contents
Page 1
High CMR Isolation Amplifiers Technical Data Features • 15 kV/ s Common-Mode Rejection 1000 V* CM • Compact, Auto-Insertable Standard 8-pin DIP Package • 4 Offset Drift vs. Temperature • 0.9 mV Input Offset Voltage ...
Page 2
... Gain Tol.; Mean Gain Value = 8.07 Option yyy 300 = Gull Wing Surface Mount Lead Option 500 = Tape/Reel Package Option (1 k min.) Option datasheets available. Contact your Hewlett-Packard sales representative or authorized distributor for information. Package Outline Drawings Standard DIP Package 9.40 (0.370) 9.90 (0.390) ...
Page 3
Gull Wing Surface Mount Option 300* 9.65 ± 0.25 (0.380 ± 0.010 7800 YYWW MOLDED 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± 0.013) 2.540 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). TOLERANCES (UNLESS ...
Page 4
Regulatory Information The HCPL-7800 has been approved by the following organizations: UL Recognized under UL 1577, Component Recognition Program, File E55361. Insulation and Safety Related Specifications Parameter Symbol Min. External Air Gap L(IO1) (External Clearance) Min. External Tracking L(IO2) Path ...
Page 5
Absolute Maximum Ratings Parameter Storage Temperature Ambient Operating Temperature Supply Voltages Steady-State Input Voltage Two Second Transient Input Voltage Output Voltages Lead Solder Temperature (1.6 mm below seating plane, 10 sec.) Reflow Temperature Profile Recommended Operating Conditions Parameter Ambient Operating ...
Page 6
DC Electrical Specifications All specifications and figures are at the nominal operating condition of V 5.0 V, and V = 5.0 V, unless otherwise noted. DD2 Parameter Symbol Input Offset Voltage V OS Input Offset Drift vs. dV /dT OS ...
Page 7
AC Electrical Specifications All specifications and figures are at the nominal operating condition 5.0 V, and V = 5.0 V, unless otherwise noted. DD1 DD2 Parameter Symbol Rising Edge Isolation IMR Mode Rejection Falling Edge Isolation ...
Page 8
Notes: General Note: Typical values represent the mean value of all characterization units at the nominal operating conditions. Typical drift specifications are determined by calculating the rate of change of the speci- fied parameter versus the drift parameter (at nominal ...
Page 9
Short circuit current is the amount of output current generated when either output is shorted ground. DD2 26. IMR (also known as CMR or Common Mode Rejection) specifies the mini- mum rate of rise of an ...
Page 10
MEAN ± 2 SIGMA 400 200 0 -200 -400 -600 4.4 4.6 4.8 5.0 5.2 5.4 5.6 V – INPUT SUPPLY VOLTAGE – V DD1 Figure 3. Input-Referred Offset Drift vs V). DD1 DD2 +5 ...
Page 11
MEAN ± 2 SIGMA 0.10 0.05 0 -0.05 -0.10 -40 - 100 T – TEMPERATURE – °C A Figure 10. 200 mV Nonlinearity Drift vs. Temperature. 0.15 0.10 0.05 0 -0.05 -0.10 -0.15 MEAN ...
Page 12
V 78L05 HCPL-7800 OUT 2 7 0.1 µF 0.1 µ PULSE GEN Figure 19. Isolation Mode Rejection Test Circuit Figure 20. Typical ...
Page 13
OUT +5 V HCPL-7800 0.1 µ 0.01 µF 4 Figure 22. Propagation Delay and Rise/Fall Time Test Circuit -10 -1 -15 -2 -30 -3 -45 AMPLITUDE PHASE -4 -60 ...
Page 14
FLOATING POSITIVE SUPPLY HV+ GATE DRIVE CIRCUIT IN OUT U1 78L05 C1 0.1 µ MOTOR - + R SENSE HV- Figure 26. Recommended Application Circuit. 400 OUTPUT POWER INPUT POWER 300 200 100 0 ...
Page 15
Circuit Information The recommended application circuit is shown in Figure 26. A floating power supply (which in many applications could be the same supply that is used to drive the high-side power transistor) is regulated using a ...
Page 16
To maintain circuit accuracy recommended that the sense resistor and the isolation amplifier circuit be located as close as ...
Page 17
Figure 30. Application Circuit Sine Wave Response. Figure 31. Application Circuit Square Wave Response. Figure 32. Application Circuit Overload Recovery Waveform. 1-232 ...