P82C150AFT Philips Semiconductors, P82C150AFT Datasheet

no-image

P82C150AFT

Manufacturer Part Number
P82C150AFT
Description
CAN Serial Linked I/O device SLIO with digital and analog port functions
Manufacturer
Philips Semiconductors
Datasheet
Preliminary specification
Supersedes data of 1995 Oct 11
File under Integrated Circuits, IC18
DATA SHEET
P82C150
CAN Serial Linked I/O device
(SLIO) with digital and analog port
functions
INTEGRATED CIRCUITS
1996 Jun 19

Related parts for P82C150AFT

P82C150AFT Summary of contents

Page 1

DATA SHEET P82C150 CAN Serial Linked I/O device (SLIO) with digital and analog port functions Preliminary specification Supersedes data of 1995 Oct 11 File under Integrated Circuits, IC18 INTEGRATED CIRCUITS 1996 Jun 19 ...

Page 2

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions CONTENTS 1 FEATURES 2 GENERAL DESCRIPTION 3 ORDERING INFORMATION 4 BLOCK DIAGRAM 5 FUNCTIONAL DIAGRAM 6 PINNING INFORMATION 6.1 Pinning 6.2 Pin description 7 FUNCTIONAL DESCRIPTION 7.1 I/O functions 7.2 I/O registers 7.3 CAN functions 7.4 Initialization 7.5 P82C150 operation after RESET or change of bus mode ...

Page 3

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 1 FEATURES Single-chip I/O device with CAN protocol controller Meets CAN protocol specification version 2.0 A and B (passive) with restricted bit timing Fully integrated clock oscillator (no crystal required) 16 configurable digital or analog I/O port pins ...

Page 4

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 4 BLOCK DIAGRAM +5 V handbook, full pagewidth bus mode RXO 21 CAN-bus RX1 22 input comparator 19 REFERENCE REF VOLTAGE RST 23 bus mode + TX1 26 CAN-bus TX0 25 1996 Jun clock ...

Page 5

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 5 FUNCTIONAL DIAGRAM handbook, full pagewidth RX0 CAN-bus inputs RX1 reference REF voltage output TX1 CAN-bus outputs TX0 RST (reset) XMOD 1996 Jun P16 ADC feedback output ...

Page 6

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 6 PINNING INFORMATION 6.1 Pinning handbook, halfpage 1996 Jun P0/CLK TX1 TX0 XMOD RST RX1 P82C150 RX0 ...

Page 7

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 6.2 Pin description Table 1 Pin description for P82C150; SO28; see note 1 SYMBOL PIN P2 1 I/O Ports P2 to P3; Identifier programming input I/O Port 4; DPM2 output Ground, digital part (0 V; logic circuits and CAN-bus driver). ...

Page 8

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 7 FUNCTIONAL DESCRIPTION 7.1 I/O functions The P82C150 provides 16 port pins (P15 to P0) which are individually configurable via CAN-bus. Besides the digital I/O functions some of these port pins provide analog I/O functions. 7.1.1 D IGITAL INPUT FUNCTIONS ...

Page 9

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 7.2 I/O registers 1996 Jun 19 9 Preliminary specification P82C150 ...

Page 10

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 7.2 ATA NPUT EGISTER DDRESS This read only register contains the states of port pins P15 to P0 which are transmitted on request, or automatically by change of one of the input levels, provided that the respective input is configured to event capture mode (see Table 3) ...

Page 11

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 7.2 NALOG ONFIGURATION This read/write register contains the bits ADC, OC3 to OC1 and SW3 to SW1 (see Fig.7). ADC bit (analog-to-digital conversion start bit; write only bit). The P82C150 starts an analog-to-digital conversion cycle at ADC = 1 ended with the transmission of a message containing the result ...

Page 12

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions ok, full pagewidth P16 17 R2 P15 P14 P13 13 P12 12 P11 11 P10 3 P4 Fig.5 Analog configuration of I/O port pins; R1, R2 and C1 are used to implement the analog-to-digital converter. ...

Page 13

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions handbook, full pagewidth H DPM = DPM = DPM = DPM = DPM = 512 L H DPM = 513 L H DPM = 1023 L Distributed Pulse Modulation (DPM special pulse count modulation. ...

Page 14

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 7.3 CAN functions The P82C150 meets the CAN protocol specification version 2.0 A and B (passive) with restricted bit timing because of the on-chip RC-oscillator and the automatic bit rate detection system with P82C150 nodes there must be at least one conventional crystal-driven CAN controller (host node) which is compatible to the CAN specification V1 ...

Page 15

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 7.3 RANSMISSION OF ATA RAMES Data Frames transmitted by the P82C150 contain three data bytes (see Fig.7). The first data byte contains the status information and the register address (see Tables 8 and 9), the other two data bytes contain the content of the addressed I/O Register ...

Page 16

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions Table 8 Data Frame Byte 1 STATUS RSTD EW Table 9 Description of Data Frame Byte 1 bits SYMBOL Status RSTD It is logic 1 in the first message (‘sign-on’ message) after the successful detection of the bit rate (bit time calibrated) ...

Page 17

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 7.3.4 CAN- BUS MODES The P82C150 can pass through four CAN-bus modes under certain conditions (see Fig.8). In the bus modes (see Table 10) the P82C150 is operating with different input comparator configurations. Bus mode 3 is the power reduced Sleep Mode ...

Page 18

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 7.3 IMING The Nominal Bit Time of the P82C150 is subdivided into 10 Time Quanta. The Synchronization Time Segment (SYNC_SEG) and the Propagation Time Segment (PROP_SEG) are each one Time Quantum long. The ...

Page 19

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 7.3.7 T RANSMIT AND RECEIVE LOGIC The transmit and receive logic stores the destuffed bit stream which was received or is about to be transmitted. The incoming Identifier is compared with that of the P82C150 ...

Page 20

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 7.4 Initialization 7.4.1 I DENTIFIER PROGRAMMING Most of the P82C150 identifier bits are fixed. Four bits are programmable via port pins P3 to P0. All output drivers are disabled at reset, also P3 to P0. Thus the outputs are floating unless the input level is defined by external components to define identifier bits ...

Page 21

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 7.5 P82C150 operation after RESET or change of bus mode Figure 9 illustrates the calibration procedure of the P82C150 after Power-on-reset or after a bus mode change. andbook, full pagewidth end of Power-on-reset ID bits from P0-P3 latched Fig ...

Page 22

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 8 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL V supply voltage input voltage on any pin I (RX0, RX1, TX0, TX1 excluded) I RX1 and RX0 input current ...

Page 23

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 9 DC CHARACTERISTICS 4 +85 C and amb SYMBOL PARAMETER Supply V supply voltage DD I operating supply current DD I supply current Sleep mode DD(SM) CAN Input comparators RX0 and RX1 ...

Page 24

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions SYMBOL PARAMETER OC1 comparator input P15 V input switch-over voltage i sw lower threshold upper threshold I input leakage current LI2 C analog input capacitance IA Analog switches; ION = resistance ON Notes to the DC characteristics: 1 ...

Page 25

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 11 APPLICATION INFORMATION 11.1 Maximum bus length The bit timing parameters refer to using a P8xCE598 or P8xC592 microcontroller with on-chip CAN interface as a host node (see Fig.20). Table 15 Maximum bus length for CAN-bus systems with P82C150 nodes. ...

Page 26

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions handbook, full pagewidth MHA079 (1) Bit SR.5 in Status Register. Fig.11 P82C150 start-up bit time calibration procedure for host node (P8xC592, P8xCE598 or P82C200). 1996 Jun 19 Load calibration message into transmit buf fer ...

Page 27

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 11.3 External oscillator mode In this mode the P82C150 operates with an external clock instead with the on-chip RC-oscillator. Figure 14 shows the application with an external clock. In this mode the P82C150 can achieve bit rates below 20 kbit/s and above 125 kbit/s ...

Page 28

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 11.6 Using ADC The application in Fig.16 can be used for analog-to-digital conversion for only one analog input signal. The evaluation of ADC were done with the values 100 k and C = 3.3 nF; under these conditions the ADC may reach an accuracy bit (depends on application) ...

Page 29

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions dbook, full pagewidth comparison between two analog input signals message transmission when analog input signal exceeds threshold voltage message transmission when analog input signal exceeds upper respectively lower threshold voltage ...

Page 30

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions handbook, full pagewidth V bat on/off LOAD control D BUK101-50GS (digital out) RST RX0 Fig.19 Examples of TOPFET applications with P82C150. 1996 Jun 19 V bat linear control with ...

Page 31

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 11.8 CAN-bus system applications 1996 Jun 19 31 Preliminary specification P82C150 pagewidth full handbook, ...

Page 32

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 12 PACKAGE OUTLINE SO28: plastic small outline package; 28 leads; body width 7 pin 1 index 1 e DIMENSIONS (inch dimensions are derived from the original mm dimensions) A UNIT max. ...

Page 33

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 13 SOLDERING 13.1 Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities ...

Page 34

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 14 DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. ...

Page 35

... Philips Semiconductors CAN Serial Linked I/O device (SLIO) with digital and analog port functions 1996 Jun 19 NOTES 35 Preliminary specification P82C150 ...

Page 36

... Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +1 800 234 7381, Fax. +1 708 296 8556 Middle East: see Italy For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. + 24825 © Philips Electronics N.V. 1996 All rights are reserved ...

Related keywords