LPC1113FHN33/203,5 NXP Semiconductors, LPC1113FHN33/203,5 Datasheet - Page 244
LPC1113FHN33/203,5
Manufacturer Part Number
LPC1113FHN33/203,5
Description
ARM Microcontrollers - MCU Cortex-M0 24 kB flash up to 8kB SRAM
Manufacturer
NXP Semiconductors
Datasheet
1.LPC1113FHN333035.pdf
(538 pages)
Specifications of LPC1113FHN33/203,5
Rohs
yes
Core
ARM Cortex M0
Processor Series
LPC1113
Data Bus Width
32 bit
Maximum Clock Frequency
50 MHz
Program Memory Size
24 KB
Data Ram Size
4 KB
On-chip Adc
Yes
Operating Supply Voltage
1.8 V to 3.6 V
Operating Temperature Range
- 65 C to + 150 C
Package / Case
HVQFN-33
Mounting Style
SMD/SMT
Factory Pack Quantity
260
- Current page: 244 of 538
- Download datasheet (5Mb)
NXP Semiconductors
UM10398
User manual
15.8.3 Slave Receiver mode
After a Repeated START condition, I
In the slave receiver mode, data bytes are received from a master transmitter. To initialize
the slave receiver mode, write any of the Slave Address registers (ADR0-3) and write the
I
Table 232. I2C0CONSET and I2C1CONSET used to configure Slave mode
I2EN must be set to 1 to enable the I
its own slave address or the General Call address. The STA, STO and SI bits are set to 0.
After ADR and CONSET are initialized, the I
own address or general address followed by the data direction bit. If the direction bit is 0
(W), it enters slave receiver mode. If the direction bit is 1 (R), it enters slave transmitter
mode. After the address and direction bit have been received, the SI bit is set and a valid
status code can be read from the Status register (STAT). Refer to
codes and actions.
2
Bit
Symbol
Value
Fig 46. Format of Master Receiver mode
Fig 47. A Master Receiver switches to Master Transmitter after sending Repeated START
C Control Set register (CONSET) as shown in
S
S
from Master to Slave
from Slave to Master
From master to slave
From slave to master
SLA
SLAVE ADDRESS
7
-
-
R
All information provided in this document is subject to legal disclaimers.
A
Rev. 12 — 24 September 2012
6
I2EN
1
DATA
n bytes data transmitted
RW=1
5
STA
0
A
Chapter 15: LPC111x/LPC11Cxx I2C-bus controller
2
2
A
DATA
C may switch to the master transmitter mode.
C function. AA bit must be set to 1 to acknowledge
4
STO
0
2
A
DATA
C interface waits until it is addressed by its
A = Acknowledge (SDA low)
A = Not acknowledge (SDA high)
S = START condition
P = STOP condition
Table
Sr
3
SI
0
232.
SLA
n bytes data received
A = Acknowledge (SDA low)
A = Not acknowledge (SDA high)
S = START condition
P = STOP condition
SLA = Slave Address
Sr = Repeated START condition
A
2
AA
1
W
DATA
Table 239
A
UM10398
1
-
-
© NXP B.V. 2012. All rights reserved.
DATA
for the status
A
A
0
-
-
244 of 538
P
P
Related parts for LPC1113FHN33/203,5
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: