AS1364-BTDT-33-1k ams, AS1364-BTDT-33-1k Datasheet
AS1364-BTDT-33-1k
Specifications of AS1364-BTDT-33-1k
Related parts for AS1364-BTDT-33-1k
AS1364-BTDT-33-1k Summary of contents
Page 1
... When in shutdown, a 5k (typ) discharge path is connected between the output pin and ground. The AS1364 is available in a 8-pin TDFN 3x3mm package. Figure 1. AS1364 - Typical Application Diagram IN ...
Page 2
... Voltage-Setting Input. Connect to GND to select the factory-preset output voltage. Connect this pin to an external resistor-divider for adjustable-output operation 7 SET/BYP Bypass Pin. Connect a 10nF capacitor from this pin to OUT to improve PSRR and noise performance. (AS1364-AD does not offer this feature) 8 GND Ground Connect to Connect to PCB metal area for heatsink purposes ...
Page 3
... AS1364 Datasheet - Absolute Maximum Ratings Stresses beyond those listed in Table 3 may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in maximum rating conditions for extended periods may affect device reliability ...
Page 4
... AS1364 Datasheet - Electrical Characteristics Note: All limits are guaranteed. The parameters with min and max values are guaranteed by production tests or SQC (Statistical Quality Control) methods 500mV +2.0V (whichever is greater),C ...
Page 5
... AS1364 Datasheet - Table 4. Electrical Characteristics (Continued) Symbol Parameter Shutdown I Shutdown Supply Current OFF Input Threshold Input Bias Current SHDNN POK Output V POK Output Low Voltage OL Operating Voltage Range for Valid ...
Page 6
... AS1364 Datasheet - Typical Operating Characteristics 0.5V 4.7µ OUT(NOM) IN OUT Figure 3. V vs. I DROP OUT 160 140 120 100 200 400 600 Load Current (mA) Figure 5 ...
Page 7
... AS1364 Datasheet - Figure 9. Quiescent Current vs. Temperature -45 -30 - Temperature (°C) Figure 11. PSRR vs. Frequency 10mA OUT 100 0.01 1 100 Frequency (kHz) www ...
Page 8
... AS1364 Datasheet - Figure 12. Line Transient Response 3.8V to 4.3V 100mA IN OUT 100µs/Div Figure 14. Startup 3.8V 100mA IN OUT 1ms/Div www.austriamicrosystems.com Figure 13. Load Transient Response 3.8V 50mA to 500mA ...
Page 9
... Datasheet - Detailed Description The AS1364 output voltage is factory-trimmed or is adjustable from +1.2V to +5V, and is guaranteed to supply 1A of output current. The device consists of a +1.20V internal reference, error amplifier, MOSFET driver, P-channel pass transistor, internal feedback voltage-divider and a ...
Page 10
... GND 8.2 Shutdown If pin EN is connected to GND the AS1364 is disabled. In shutdown mode all internal circuits are turned off, reducing supply current to 10nA (typ). For normal device operation pin EN must be connected to IN. During shutdown, POK goes low. When in shutdown, a 5k (typ) discharge path is connected between the output pin and ground. ...
Page 11
... AS1364 Datasheet - Application Information 9.1 Dropout Voltage Dropout is the input to output voltage difference, below which the linear regulator ceases to regulate. At this point, the output voltage change follows the input voltage change. Dropout voltage may be measured at different currents and, in particular at the regulator maximum one. From this is obtained the MOSFET maximum series resistance over temperature etc ...
Page 12
... AS1364 Datasheet - 9.3 Power Dissipation Maximum power dissipation (PD) of the LDO is the sum of the power dissipated by the internal series MOSFET and the quiescent current required to bias the internal voltage reference and the internal error amplifier, and is calculated as: ...
Page 13
... AS1364 Datasheet - Total Thermal Path Resistance: Junction Temperature (T ºC) is determined by: J 9.5 Explanation of Steady State Specifications 9.5.1 Line Regulation Line regulation is defined as the change in output voltage when the input (or line) voltage is changed by a known quantity measure of the regulator’ ...
Page 14
... Larger output capacitor values (10µF max) help to reduce noise and improve load transient-response, stability and power-supply rejection. 9.6.3 Input Capacitor An input capacitor required for stability recommended that a 4.7µF capacitor be connected between the AS1364 power supply IN input pin V and ground (capacitance value may be increased without limit subject to ESR limits). This capacitor must be located at a distance ...
Page 15
... To prevent operation under extreme fault conditions, such as a permanent short circuit at the output, thermal protection is built into the device. Die temperature is measured, and when a 170ºC (AS1364) threshold is reached, the device enters shutdown. When the die cools sufficiently, the device will restart (assuming input voltage exists and the device is enabled). Hysteresis of 20ºC prevents low frequency oscillation between start- up and shutdown around the temperature threshold ...
Page 16
... AS1364 Datasheet - Package Drawings and Markings The device is available in an 8-pin TDFN 3x3mm package. Figure 21. 8-pin TDFN 3x3mm Package D PIN 1 INDEX AREA aaa C 2x (D/2 xE/2) 4 TOP VIEW e Term inal Tip ...
Page 17
... AS1364 Datasheet - Revision History Revision Date - - 1.5 Sep 2011 1.6 18 Nov, 2011 1.7 12 Dec, 2011 1.8 03 Apr, 2012 Note: Typos may not be explicitly mentioned under revision history. www.austriamicrosystems.com Owner - Changes made across document ...
Page 18
... Ordering Code Marking AS1364-BTDT-AD ASRF AS1364-BTDT-12* ASRN AS1364-BTDT-15 ASRG AS1364-BTDT-18 ASRH AS1364-BTDT-30 ASRJ AS1364-BTDT-33 ASRI AS1364-BTDT-45 ASRK *Future product. Non-standard devices are available between 1.4V and 4.6V in 50mV steps and between 4.6V and 5.0V in 100mV steps. For more information and inquiries contact http://www.austriamicrosystems.com/contact Note: All products are RoHS compliant. ...
Page 19
... AS1364 Datasheet - Copyrights Copyright © 1997-2012, austriamicrosystems AG, Tobelbaderstrasse 30, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered ®. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner ...