25AA640-I/SN Microchip Technology, 25AA640-I/SN Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
25AA640-I/SN
Manufacturer Part Number
25AA640-I/SN
Description
IC EEPROM 64KBIT 1MHZ 8SOIC
Manufacturer
Microchip Technology
Datasheet
1.25LC640-ESN.pdf
(24 pages)
Specifications of 25AA640-I/SN
Memory Size
64K (8K x 8)
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Speed
1MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Memory Configuration
8K X 8
Ic Interface Type
SPI
Clock Frequency
1MHz
Supply Voltage Range
1.8V To 5.5V
Memory Case Style
SOIC
No. Of Pins
8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
25AA640-I/SNG
25AA640-I/SNG
25AA640-I/SNG
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
25AA640-I/SN
Manufacturer:
MCP
Quantity:
5 371
Company:
Part Number:
25AA640-I/SN
Manufacturer:
MICROCHIP
Quantity:
12 000
Part Number:
25AA640-I/SN
Manufacturer:
MICROCHI
Quantity:
20 000
3.0
3.1
The 25XX640 is a 8192 byte Serial EEPROM designed
to interface directly with the Serial Peripheral Interface
(SPI) port of many of today’s popular microcontroller
families, including Microchip’s PIC16C6X/7X micro-
controllers. It may also interface with microcontrollers
that do not have a built-in SPI port by using discrete
I/O lines programmed properly with the software.
The 25XX640 contains an 8-bit instruction register. The
device is accessed via the SI pin, with data being
clocked in on the rising edge of SCK. The CS pin must
be low and the HOLD pin must be high for the entire
operation.
Table 3-1 contains a list of the possible instruction
bytes and format for device operation. All instructions,
addresses, and data are transferred MSB first, LSB
last.
Data is sampled on the first rising edge of SCK after CS
goes low. If the clock line is shared with other
peripheral devices on the SPI bus, the user can assert
the HOLD input and place the 25XX640 in ‘HOLD’
mode. After releasing the HOLD pin, operation will
resume from the point when the HOLD was asserted.
3.2
The device is selected by pulling CS low. The 8-bit
READ instruction is transmitted to the 25XX640 fol-
lowed by the 16-bit address with the three MSBs of the
address being “don’t care” bits. After the correct READ
instruction and address are sent, the data stored in the
memory at the selected address is shifted out on the
SO pin. The data stored in the memory at the next
address can be read sequentially by continuing to pro-
vide clock pulses. The internal Address Pointer is auto-
matically incremented to the next higher address after
each byte of data is shifted out. When the highest
address is reached (1FFFh), the address counter rolls
over to address 0000h allowing the read cycle to be
continued indefinitely. The read operation is terminated
by raising the CS pin (Figure 3-1).
TABLE 3-1:
© 2008 Microchip Technology Inc.
Instruction Name
WRITE
READ
WREN
WRDI
RDSR
WRSR
FUNCTIONAL DESCRIPTION
Principles Of Operation
Read Sequence
INSTRUCTION SET
Instruction Format
0000 0011
0000 0010
0000 0110
0000 0100
0000 0101
0000 0001
Read data from memory array beginning at selected address
Write data to memory array beginning at selected address
Set the write enable latch (enable write operations)
Reset the write enable latch (disable write operations)
Read STATUS register
Write STATUS register
3.3
Prior to any attempt to write data to the 25XX640 array
or STATUS register, the write enable latch must be set
by issuing the WREN instruction (Figure 3-4). This is
done by setting CS low and then clocking out the
proper instruction into the 25XX640. After all eight bits
of the instruction are transmitted, the CS must be
brought high to set the write enable latch. If the write
operation is initiated immediately after the WREN
instruction without CS being brought high, the data will
not be written to the array because the write enable
latch will not have been properly set.
Once the write enable latch is set, the user may
proceed by setting the CS low, issuing a WRITE
instruction, followed by the address, and then the data
to be written. Up to 32 bytes of data can be sent to the
25XX640 before a write cycle is necessary. The only
restriction is that all of the bytes must reside in the
same page. A page address begins with XXX0 0000
and ends with XXX1
counter reaches XXX1 1111 and the clock continues,
the counter will roll back to the first address of the page
and overwrite any data in the page that may have been
written.
For the data to be actually written to the array, the CS
must be brought high after the Least Significant bit (D0)
of the n
brought high at any other time, the write operation will
not be completed. Refer to Figure 3-2 and Figure 3-3
for more detailed illustrations on the byte write
sequence and the page write sequence, respectively.
While the write is in progress, the STATUS register may
be read to check the status of the WPEN, WIP, WEL,
BP1, and BP0 bits (Figure 3-6). A read attempt of a
memory array location will not be possible during a
write cycle. When the write cycle is completed, the
write enable latch is reset.
25AA640/25LC640
th
Write Sequence
data byte has been clocked in. If CS is
Description
1111. If the internal address
DS21223H-page 7