ZLF645S2864GP0001T Maxim Integrated, ZLF645S2864GP0001T Datasheet - Page 77
ZLF645S2864GP0001T
Manufacturer Part Number
ZLF645S2864GP0001T
Description
8-bit Microcontrollers - MCU Crimzon Flash Infrared MCU
Manufacturer
Maxim Integrated
Datasheet
1.ZLF645E0H4864G2204.pdf
(201 pages)
Specifications of ZLF645S2864GP0001T
Core
Z8
Data Bus Width
8 bit
Maximum Clock Frequency
8 MHz
Program Memory Size
64 KB
Data Ram Size
1 KB
Operating Supply Voltage
2 V to 3.6 V
Interface Type
UART
Number Of Programmable I/os
5
Number Of Timers
2 x 8 bit, 1 x 16 bit
Processor Series
ZLF645
Program Memory Type
Flash
- Current page: 77 of 201
- Download datasheet (2Mb)
Flash Controller Overview
19-4572; Rev 0; 4/09
Caution:
Executing Flash Memory Accesses Through the Flash Controller
Pages 0 through 2 (addresses
for Maxim
the ICP interface or by using the Flash Byte Programming interface.
The Flash Controller provides the appropriate Flash controls and timing for byte/word
programming, Page Erase, Mass Erase, and reading of the Flash memory for Flash
accesses made by either the CPU or through the ICP interface. It also limits programming,
erase, and read access to the Flash memory based upon certain register and/or option bit
settings. External accesses through the ZLF645’s ICP or Flash Byte Programming Inter-
faces are limited by the Flash Controller based upon the programming of the ZLF645’s
Flash read/write protect bits in User Option Byte 1. Accesses by the CPU during code exe-
cution is limited based upon the programming of the Flash Controller’s Sector Protect
(FSEC) registers. All Flash memory accesses through the Flash Controller are prevented
unless the Flash Controller is in ‘unlocked’ state.
Flash Access Timing Control Programming Requirements
Before a program or erase operation can be executed by the Flash Controller on the Flash
memory, you must first configure the Flash Controller’s Flash frequency High and Low
Byte registers. These registers combine to form a 16-bit value (FFREQ) that is used by the
Flash Controller to control timing for Flash program and erase operations. For proper tim-
ing, the 16-bit binary Flash Frequency value must be programmed with the system clock
frequency (in kHz).
This 16-bit binary Flash Frequency value is calculated using the following equation:
Using a 16-bit value FFREQ value, the Flash Controller is able to provide correct program
and erase operation timing across a CPU clock frequency range of 1 MHz to 8 MHz.
The System Clock Frequency depends on the Flash memory programming of bit 2 of the
User Option Byte 1 and on the register programming of bit 0 of the SMR register and can
be equal to the clock input frequency on the XTAL1 pin, a divide by 2 of that input, a divide
by 16 of that input, or a divide by 32 of that input. Flash programming and erasure are not
supported for CPU clock frequencies below 1 MHz or above 8 MHz. The Flash Frequency
High and Low Byte registers must be loaded with the correct values.
FFREQ[15:0]
®
internal use and are inaccessible by you or programmer vendor, either through
=
System Clock Frequency (Hz)
------------------------------------------------------------------------------ -
0000
1000
through
00BF
), of the Information Area are reserved
ZLF645 Series Flash MCUs
Product Specification
Flash Controller Overview
69
Related parts for ZLF645S2864GP0001T
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: