AT88SC0104C-MP Atmel, AT88SC0104C-MP Datasheet
![no-image](/images/manufacturer_photos/0/0/78/atmel_sml.jpg)
AT88SC0104C-MP
Specifications of AT88SC0104C-MP
Related parts for AT88SC0104C-MP
AT88SC0104C-MP Summary of contents
Page 1
... Same Pinout as 2-wire Serial EEPROM's • High Reliability ⎯ Endurance: 100,000 Cycles ⎯ Data Retention: 10 years ⎯ ESD Protection: 4,000V min * Note: Modules available with either T=0 / 2-wire modes or 2-wire mode only. ® CryptoMemory 1 Kbit AT88SC0104C Summary 2021KS–SMEM–10/09 ...
Page 2
... Up to four unique key sets may be used for these operations. The AT88SC0104C offers the ability to communicate with virtually any smart card reader using the asynchronous protocol (Gemplus Patent) defined in ISO 7816-3 ...
Page 3
... Reset (RST) The AT88SC0104C provides an ISO 7816-3 compliant asynchronous answer to reset sequence. When the reset sequence is activated, the device will output the data programmed into the 64-bit answer-to-reset register. An internal pull-up on the RST input pad allows the device to be used in synchronous mode without bonding RST. The AT88SC0104C does not support the synchronous answer-to-reset sequence ...
Page 4
... OH V SDA/IO Output Low Voltage OL I SDA/IO Output High Current OH Notes min and prevent Latch Up Conditions from occurring during Power Up of the AT88SCxxxxC before applying V AT88SC0104C 4 * NOTICE: Stresses beyond those listed under “Absolute +0. +2.7 to 5.5V Test Condition = 5.5V) Async READ at 3.57MHz ...
Page 5
... After an interruption in protocol, power loss or system reset, any 2-wire part can be reset by following these steps: 1. Clock cycles. 2. Look for SDA high in each cycle while SCL is high. 3. Create a start condition. AT88SC0104C Min Max Units 1 5 MHZ 1 4 ...
Page 6
... Bus Timing for 2 wire communications: SCL: Serial Clock, SDA – Serial Data I/O SCL t SU.STA SDA IN SDA OUT Figure 4. Write Cycle Timing: SCL: Serial Clock, SDA – Serial Data I/O SCL SDA 8th BIT WORDn The write cycle time t Note: clear/write cycle. AT88SC0104C 6 t HIGH LOW LOW t t HD.STA HD.DAT t ...
Page 7
... Figure 5. Data Validity SDA SCL DATA STABLE Figure 6. Start and Stop Definitions SDA SCL START Figure 7. Output Acknowledge SCL DATA IN DATA OUT 2021KS–SMEM–10/09 DATA STABLE DATA CHANGE ALLOWED STOP AT88SC0104C ...
Page 8
... Access to the user zones occurs only through the control logic built into the device. This logic is configurable through access registers, key registers and keys programmed into the configuration memory during device personalization. Also implemented in the control logic is a cryptographic engine for performing the various higher-level security functions of the device. AT88SC0104C ...
Page 9
... For Authentication and Encryption use Write 0 PAC Write 1 PAC Write 2 PAC Write 3 PAC Write 4 PAC Write 5 PAC Write 6 PAC Write 7 PAC Reserved AT88SC0104C $6 $7 Identification Read Only AR3 PR3 Access Control Cryptography Secret Read 0 Read 1 Read 2 Read 3 Password Read 4 Read 5 Read 6 ...
Page 10
... Protocol selection The AT88SC0104C supports two different communication protocols. • Smart Card Applications: The asynchronous protocol defined by ISO 7816-3 is used for compatibility with the industry’s standard smart card readers. ...
Page 11
... Configuration data include viewable areas of the Configuration Zone except the passwords: Note: MDC: Modification Detection Code MAC: Message Authentication Code. 2021KS–SMEM–10/ (1) User Data clear clear clear clear clear encrypted AT88SC0104C due to an internal pull-up on RST. For embedded Passwords Data Integrity Check clear encrypted encrypted (1) MDC (1) MAC (1) MAC 11 ...
Page 12
... In the write lock configuration, only one byte can be written at a time. Even if several bytes are received, only the first byte will be taken into account by the device. AT88SC0104C 12 $0 ...
Page 13
... Device (Card) Card Number VERIFY A COMPUTE Challenge B Challenge B VERIFY RPW Checksum (CS) VERIFY WPW VERIFY CS Write DATA 2021KS–SMEM–10/09 AUTHENTICATION READ ACCESS DATA WRITE ACCESS AT88SC0104C Host (Reader) COMPUTE Challenge A Challenge A VERIFY B Read Password (RPW) VERIFY CS Write Password (WPW) DATA CS 13 ...
Page 14
... CryptoMemory using simple write and read commands. To gain access to the configuration memory, the secure code must first be successfully presented. For the AT88SC0104C device, the secure code is $DD 42 97. After writing and verifying data in the configuration memory, the security fuses must be blown to lock this information in the device. For additional information on personalizing CryptoMemory, please see the application notes Programming CryptoMemory for Embedded Applications and Initializing CryptoMemory for Smart Card Applications (at www ...
Page 15
... Ordering Information Ordering Code AT88SC0104C-MJ AT88SC0104C-MP AT88SC0104C-MJTG AT88SC0104C-MPTG AT88SC0104C-PU AT88SC0104C-SU AT88SC0104C-WI (1) (2) Package Type M2 – J Module : ISO or TWI M2 – P Module : ISO or TWI 8P3 8S1 1. Formal drawings may be obtained from an Atmel sales office. Note: 2. Both the J and P Module Packages are used for either ISO (T=0 / 2-wire mode) or TWI (2-wire mode only). ...
Page 16
... The module dimensions listed refer to the dimensions of the exposed metal contact area. The actual dimensions of the module after excise or punching from the carrier tape are generally 0.4 mm greater in both directions (i.e., a punched M2 module will yield 13.0 x 11.8 mm). AT88SC0104C 16 Ordering Code MPTG Round - ∅ ...
Page 17
... These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 2021KS–SMEM–10/ TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) AT88SC0104C End View COMMON DIMENSIONS (Unit of Measure = mm) MIN MAX SYMBOL NOM A 1.35 – 1. ...
Page 18
... E and eA measured with the leads const r ained to be perpendicular to datum. 5. Pointed or rounded lead tips are pre ferred to ease insertion and b3 maximum dimensions do not include Dambar prot r usions. Dambar protrusions shall not exceed 0.010 (0.25 mm). 2325 Orchard Parkway San Jose, CA 95131 R AT88SC0104C ...
Page 19
... Replace ‘Lead-free/Halogen-free. Keep industrial Updated to 2009 Copyright. 11/2008 Updated timing diagrams. Final release version. Replaced User Zone, Configuration Memory, and Write Locks Example tables with new information. 01/2007 Implemented revision history. Removed Industrial package offerings. Removed 8Y4 package offering. AT88SC0104C Comments and all 3 instances ...
Page 20
... OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’ ...