conga-MCB/Qseven congatec, conga-MCB/Qseven Datasheet

Page 1

... Qseven conga-MCB/Qseven ® Short description of the congatec Qseven Short Description Revision 1.0 mini carrier board ® ...

Page 2

... GDA Preface This short description provides information about the components, features and connectors available on the conga-MCB/Qseven mini carrier board. Disclaimer The information contained within this short description, including but not limited to any product specification, is subject to change without notice. congatec AG provides no warranty with regard to this short description or any other information contained herein and hereby expressly disclaims any implied warranties of merchantability or fitness for any particular purpose with regard to any of the foregoing ...

Page 3

... Copyright © 2011, congatec AG. All rights reserved. All text, pictures and graphics are protected by copyrights. No copying is permitted without written permission from congatec AG. congatec AG has made every attempt to ensure that the information in this document is accurate yet the information contained within is supplied “as-is”. ...

Page 4

... AG technicians and engineers are committed to providing the best possible technical support for our customers so that our products can be easily used and implemented. We request that you first visit our website at www.congatec.com for the latest documentation, utilities and drivers, which have been made available to assist you. If you still require assistance after visiting our website then please contact our technical support department by email at support@congatec.com Copyright © ...

Page 5

... AG shall in no event be liable to the end user for collateral or consequential damages of any kind. congatec AG shall not otherwise be liable for loss, damage or expense directly or indirectly arising from the use of the product or from any other cause. The sole and exclusive remedy against congatec AG, whether a claim sound in contract, warranty, tort or any other legal theory, shall be repair or replacement of the product only ...

Page 6

... Connector X38 CAN Bus ......................................................... 27 4.20 Connector X30 ATX Power Source Control ............................. 27 4.20.1 Jumper X37 ATX Power Source Mode Selector ...................... 28 4.21 Connector X34 SPI Header ..................................................... 28 4.22 Jumper X42 USB1 Client/Host Selector .................................. 29 Copyright © 2012 congatec AG 4.23 Power and Reset Buttons ........................................................ 29 5 Additional Features .................................................................. 30 5.1 Red LEDs ................................................................................. 30 5.2 PC Speaker (Beeper) ............................................................... 30 5 ...

Page 7

... Feature connector for Power, Reset, Sleep, and LID button, LED indicators, mini card Wifi radio On/Off Note Information about the cables required to operate the conga-MCB/Qseven mini carrier board can be found in section 6 “Cables” of this document. Copyright © 2012 congatec AG module mini carrier board. It has an industrial 5 pin power connector with an input voltage allowance ® ...

Page 8

... Adobe ‘Zoom-In-Tool’ and zoom given component to see its designator. Hover over the component and the ‘Zoom-In-Tool’ will change indicating there is a link. Click on the link to navigate to the area in the document where the component is described. Use the mouse icon in the top left hand corner of the destination page to return to the connector layout pictures. Copyright © 2012 congatec AG QMCBm10 8/34 ...

Page 9

... Bottom Side conga-MCB/Qseven Copyright © 2012 congatec AG QMCBm10 9/34 ...

Page 10

... Operation: 10% to 90% Note The above operating temperatures must be strictly adhered to at all times. The maximum operating temperature refers to any measurable spot on the modules surface. Humidity specifications are for non-condensing conditions. Copyright © 2012 congatec AG Storage: -20° to +80°C Storage 95% QMCBm10 10/34 ...

Page 11

... Connector Descriptions The following tables describe the pin assignments for the connectors found on the conga-MCB/Qseven. 4.1 Connector CN1 Pinout Pin Signal Description 1 GND Power Ground 3 GBE_MDI3- Gigabit Ethernet MDI3- 5 GBE_MDI3+ Gigabit Ethernet MDI3+ 7 GBE_LINK100# 100 Mbps link speed 9 GBE_MDI1- Gigabit Ethernet MDI1- ...

Page 12

... General Purpose I2C Clock line 129 CAN0_TX CAN TX Output for CAN Bus Channel 0 131 SDVO_BCLK+ SDVO Clock line+ 133 SDVO_BCLK- SDVO Clock line- 135 GND Power Ground Copyright © 2012 congatec AG Pin Signal Description 62 SMB_DAT SMBus Data line 64 SMB_ALERT# SMBus Alert input ...

Page 13

... Do not connect on carrier board 209 MFG_NC1 Do not connect on carrier board 211 VCC Power supply +5VDC ±5% 213 VCC Power supply +5VDC ±5% Copyright © 2012 congatec AG Pin Signal Description 138 SDVO_FLDSTALL+ SDVO Field stall line+ 140 SDVO_FLDSTALL- SDVO Field stall line- 142 GND ...

Page 14

... Power supply +5VDC ±5% 225 VCC Power supply +5VDC ±5% 227 VCC Power supply +5VDC ±5% 229 VCC Power supply +5VDC ±5% Copyright © 2012 congatec AG Pin Signal Description 216 VCC Power supply +5VDC ±5% 218 VCC Power supply +5VDC ±5% 220 VCC Power supply +5VDC ± ...

Page 15

... Connector X1 PCIe Mini Card Socket The conga-MCB/Qseven is equipped with a PCI Express Mini Card socket. PCI Express Mini Card is a unique small size form factor optimized for mobile computing platforms equipped with communication applications such as Wireless LAN. Connector X1 on the bottom side of the conga-MCB/Qseven provides an interface to insert a standard PCIe Mini Card ...

Page 16

... Pitch Female Crimp Housing 2 Pos. (female) Harwin P/N: M20-1060200 and jumper (for WiFi Radio disable). 4.4 Connector X3 LAN The conga-MCB/Qseven is equipped with a RJ45 connector with integrated magnetics to support Gigabit Ethernet on the X3 connector. Additionally, “Link” and “Activity” LED indicators are integrated within the LAN connector. Pin ...

Page 17

... Connector X4 CFast Host Type II Push-Push A CFast socket Type II is implemented on the bottom side of conga-MCB/Qseven to provide support for the new media based on Serial ATA interface connected to Serial ATA channel 0 that originates from Qseven Connector Type Standard CFast media Type I or Type II. ...

Page 18

... Connector X5 SATA The conga-MCB/Qseven features one standard SATA connector X5 (Serial ATA channel 1), which originates from the Qseven optional second SATA connector can be fitted instead of connector X4 (CFast socket). Pin Signal 1 GND 2 TX+ 3 TX- 4 GND 5 RX- 6 RX+ 7 GND Connector Type 1.27mm Pitch Standard SATA Connector 7 Pos. (plug). ...

Page 19

... Connector X10 Dual USB 2.0 The conga-MCB/Qseven features a Dual USB connector (X10) that is connected to USB port 2 and USB port 3, which originate from the Qseven module. Support for USB 2.0 and/or 1.1 devices is dependent on the Qseven ® Pin Signal 1 +5V 2 DATA- 3 DATA+ 4 GND 4.10 Connector X11, X12 USB 2.0 Headers Additional USB 2 ...

Page 20

... Connector X35 HDMI / X36 DisplayPort A high resolution monitor can be attached to the conga-MCB/Qseven through the use of either the HDMI port on connector X35 or the DisplayPort on connector X36. Only one option (connector) is available at any given time and this option is dependant on the Qseven used. These connections support DDC detection. ...

Page 21

... Connector X14 LVDS A dual LVDS Interface is supported on the conga-MCB/Qseven via box header X14. DDC detection is included. Supply Voltage for the LCD display can be set to either 5V or 3.3V using jumper X31. Maximal output current is 1A. Pin Signal Pin 1 LVDS B TX0N 2 3 LVDS B TX0P ...

Page 22

... Note * VCC is the input power supply voltage of conga-MCB/Qseven 12V backlight inverter used 12V VCC has to be present and jumper X32 set to position 1-2. BCKL_CTRL signal is controlled by the I Connector Type X15: 2.00mm Pitch Housing connector 4 Pos. (female) JST P/N: PHR-4. ...

Page 23

... Connector X16 S/PDIF The conga-MCB/Qseven provides a S/PDIF audio interface via a 6 pin header (X16). Pin Signal Pin 1 + S/PDIF OUT 4 5 GND 6 Connector Type 2.54mm Pitch Female Crimp Housing 3 Pos. (female) Harwin P/N: M20-1060300 or 2.54mm Pitch Housing 6 Pos. (dual row, female) Harwin P/N: M20-1070300 ...

Page 24

... Connector X19 Power Supply The conga-MCB/Qseven has a 5 pin power connector that provides the ability to connect a power source starting with 20V, 5V Standby with ± optional voltage supported by ATX mode in conjunction with the power control connector X30 and the ATX cable adapter (available from congatec, see section 6 of this document for more information) ...

Page 25

... Connector X20 Power Supply Control The conga-MCB/Qseven has an 8 pin power control connector (X20) that provides a connection to a battery management module 12V power source. Pin Signal Description 1 GND Ground 2 SDA I2C bus Data 3 SCL I2C bus Clock 4 BATLOW# signal from Qseven ...

Page 26

... Connector X39 Fan A standard 3 pin header for a fan is provided on the conga-MCB/Qseven 12V fan can be connected to connector X39, the output voltage is set by jumper X40 12V fan used, then the input voltage of conga-MCB/Qseven must be +12V. Pin Signal 1 GND 2 +VDD (12V*/5V) ...

Page 27

... Connector X30 ATX Power Source Control The conga-MCB/Qseven has an 2 pin ATX power source control connector (X30) which can control an ATX power source in conjunction with the ATX cable adapter (available from congatec, see section 6 of this document for more information). Jumper X37 is associated with connector X30 ...

Page 28

... Connector Type 2.54mm Pitch Housing 5 Pos. (female) Harwin P/N: M20-1060500 or 2.54mm Pitch Housing 10 Pos. (dual row, female) Harwin P/N: M20-1070500. Copyright © 2012 congatec AG Jumper X37 module is made available on the conga-MCB/Qseven via a 10 pin header connector (X34). ® SPI Bus (X34 ...

Page 29

... Power and Reset Buttons The conga-MCB/Qseven is not equipped with a power button or a reset button due to space limitations but it does have the possibility to connect both buttons using the feature header X2. The power button is functional only if the conga-MCB/Qseven power is being supplied by an ATX power supply (for example when using the congatec ATX cable adapter for conga-MCB/Qseven, see section 6 of this document for more information) ...

Page 30

... The board-mounted speaker provides audible error code (beep code) information during POST. The speaker M14 is connected to the Qseven module’s SPEAKER signal. 5.3 Power Indication LEDs There are total of six green LEDs located on the conga-MCB/Qseven. LEDs D16-D18 indicate the presence of supply voltages on the carrier board. A detailed description of these can be found in the table below. LED Function When Lit D16 Indicates +3 ...

Page 31

... PCI Mini Card Activity LEDs There are total of six green LEDs located on the conga-MCB/Qseven. LEDs D1-D3 indicate PCIe Mini Card activity. A detailed description of these LEDs can be found in the table below. LED Function When Lit D1 WWAN - indicates activity of wireless wide area network D2 WLAN - indicates activity of wireless local area network ...

Page 32

... Backlight cable for conga-MCB/Qseven connector X15. USB 2.0 shielded high speed cable (USB B, Client) for conga-MCB/Qseven connector X11. Dual USB 2.0 shielded high speed cable (USB A) for conga-MCB/Qseven connectors X11 or X12. Power cable for conga-MCB/Qseven connector X19 and X30 for ATX power supply. ...

Page 33

... Mechanical Drawing 23.9 Copyright © 2012 congatec AG QMCBm10 33/34 ...

Page 34

... Industry Specifications The list below provides links to industry specifications of the interfaces that can be found on the conga-MCB/Qseven mini carrier board. Specification Qseven™ Specification, Revision 1.20 Qseven™ Design Guide, Revision 1.0 PCI Express Base Specification, Revision 2.0 Universal Serial Bus (USB) Specification, Revision 2.0 PCI Specification, Revision 2.2 Serial ATA Specification, Revision 1 ...