ADP5062CP-EVALZ Analog Devices, ADP5062CP-EVALZ Datasheet - Page 36

• Manufacturer Part Number: ADP5062CP-EVALZ
• Description: Power Management IC Development Tools ADP5062 Evaluation board
• Manufacturer: Analog Devices
• Type: Linear Regulators - Standardr
• Series: ADP5062r

Specifications of ADP5062CP-EVALZ

• Rohs: yes
• Product: Evaluation Boards
• Tool Is For Evaluation Of: ADP5062
• Input Voltage: 4 V to 6.7 V
• Description/function: Battery charger (isolated flyback)
• Interface Type: I2C
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Output Current: 2.1 A
• Factory Pack Quantity: 1
• For Use With: ADP5062

ADP5062
APPLICATIONS INFORMATION
EXTERNAL COMPONENTS
ISO_Sx (V
To obtain stable operation of the
combined effective capacitance of the ISO_Sx capacitor and the
system capacitance must not be less than 10 µF and must not
exceed 100 µF at any point during operation.
When choosing the capacitor value, it is also important to account
for the loss of capacitance caused by the output voltage dc bias.
Ceramic capacitors are manufactured with a variety of dielectrics,
each with a different behavior over temperature and applied
voltage. Capacitors must have a dielectric that is adequate to ensure
the minimum capacitance over the necessary temperature range
and dc bias conditions. X5R or X7R dielectrics with a voltage rating
of 6.3 V or higher are recommended for best performance. Y5V
and Z5U dielectrics are not recommended for use with any dc-
to-dc converter because of their poor temperature and dc bias
characteristics.
The worst case capacitance accounting for capacitor variation
over temperature, component tolerance, and voltage is calcu-
lated using the following equation:
where:
C
TEMPCO is the worst case capacitor temperature coefficient.
TOL is the worst case component tolerance.
In this example, the worst case temperature coefficient (TEMPCO)
over the range of −40°C to +85°C is assumed to be 15% for an
X5R dielectric. The tolerance of the capacitor (TOL) is assumed
to be 10%, and C
EFF
Figure 38. Murata GRM31CR61A226KE19 Capacitance vs. Bias Voltage
is the effective capacitance at the operating voltage.
C
EFF
60
55
50
45
40
35
30
25
20
= C
0
OUT
OUT
) Capacitor Selection
× (1 − TEMPCO) × (1 − TOL)
OUT
1
is 16 μF at 4.2 V, as shown in Figure 38.
DC BIAS VOLTAGE (V)
2
ADP5062
3
in a safe way, the
4
5
Rev. 0 | Page 36 of 44
Substituting these values in the equation yields
To guarantee the performance of the charger in various operating
modes, including trickle charge, constant current charge, and
constant voltage charge, it is imperative that the effects of dc
bias, temperature, and tolerances on the behavior of the capaci-
tors be evaluated for each application.
Splitting ISO_Sx Capacitance
In many applications, the total ISO_Sx capacitance consists of a
number of capacitors. The system voltage node (ISO_Sx) usually
supplies a single regulator or a number of ICs and regulators,
each of which requires a capacitor close to its power supply
input (see Figure 39).
The capacitance close to the ADP5062 ISO_Sx output should be
at least 5 µF, as long as the total effective capacitance is at least
10 µF at any point during operation.
ISO_Bx and ISO_Sx Capacitor Selection
The ISO_Bx and the ISO_Sx effective capacitance (including
temperature and dc bias effects) must not be less than 10 µF at
any point during operation. Typically, a nominal capacitance of
22 µF is required to fullfill the condition at all points of
operation. Suggestions for ISO_Bx and ISO_Sx capacitors are
listed in Table 34.
CBP Capacitor Selection
The internal supply voltage of the
noise suppressing capacitor at the CBP terminal. Do not allow CBP
capacitance to exceed 14 nF at any point during operation. Do
not connect any external voltage source, any resistive load, or
any other current load to the CBP terminal. Suggestions for a
CBP capacitor are listed in Table 35.
C
EFF
ADP5062
+
= 16 μF × (1 − 0.15) × (1 − 0.1) ≈ 12.24 μF
ISO_Sx
C
≥10µF
Figure 39. Splitting ISO_Sx Capacitance
ISO_Bx
C
ISO_Sx
> 5µF
C
IN2
ADP5062
C
SUM OF EFFECTIVE
CAPACITANCES
ON ISO_Sx NODE > 10µF
IN1
VIN2
VIN1
is equipped with a
Data Sheet
IC1
IC2