AT49BV002ANT-70PI Atmel, AT49BV002ANT-70PI Datasheet
AT49BV002ANT-70PI
Specifications of AT49BV002ANT-70PI
Related parts for AT49BV002ANT-70PI
AT49BV002ANT-70PI Summary of contents
Page 1
... A13 4 29 A14 5 28 A17 VCC 8 25 *RESET 9 24 A16 10 23 A15 11 22 A12 2-megabit (256K x 8) Single 2.7-volt Battery-Voltage Flash Memory AT49BV002A AT49BV002AN AT49BV002AT AT49BV002ANT OE A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 GND I/O2 I/O1 I/ Rev. 3353D–FLASH–8/03 ™ 1 ...
Page 2
... The device is erased by executing the erase command sequence; the device internally con- trols the erase operations. There are two 8K byte parameter block sections, four main memory blocks, and one boot block. The device has the capability to protect the data in the boot block; this feature is enabled by a command sequence ...
Page 3
... CHIP ERASE: If the boot block lockout has been enabled, the Chip Erase function will erase Parameter Block 1, Parameter Block 2, Main Memory Block but not the boot block. If the Boot Block Lockout has not been enabled, the Chip Erase function will erase the entire chip. ...
Page 4
... This feature is not available on the AT49BV002AN(T). PRODUCT IDENTIFICATION: The product identification mode identifies the device and man- ufacturer as Atmel. It may be accessed by hardware or software operation. The hardware operation mode can be used by an external programmer to identify the correct programming algorithm for the Atmel product. ...
Page 5
DATA POLLING: The AT49BV002A(N)(T) features DATA polling to indicate the end of a pro- gram cycle. During a program cycle an attempted read of the last byte loaded will result in the complement of the loaded data on I/O7. Once ...
Page 6
... SA = 3A000 to 3BFFF for PARAMETER BLOCK 38000 to 39FFF for PARAMETER BLOCK 30000 to 37FFF for MAIN MEMORY ARRAY BLOCK 20000 to 2FFFF for MAIN MEMORY ARRAY BLOCK 10000 to 1FFFF for MAIN MEMORY ARRAY BLOCK 00000 to 0FFFF for MAIN MEMORY ARRAY BLOCK 4 Absolute Maximum Ratings Temperature Under Bias................................ -55° ...
Page 7
DC and AC Operating Range Operating Temperature (Case) V Power Supply CC Operating Modes Mode CE Read V IL (2) Program/Erase V IL Standby/Write Inhibit V IH Program Inhibit X Program Inhibit X Output Disable X Reset X Product Identification ...
Page 8
AC Read Characteristics Symbol Parameter t Address to Output Delay ACC ( Output Delay CE ( Output Delay OE (3)( Output Float DF t Output Hold from OE, CE ...
Page 9
Input Test Waveform and Measurement Level DRIVING LEVELS Output Load Test Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. This parameter is characterized ...
Page 10
AC Byte Load Characteristics Symbol Parameter Address, OE Set-up Time AS OES t Address Hold Time AH t Chip Select Set-up Time CS t Chip Select Hold Time CH t Write Pulse Width (WE or CE) WP ...
Page 11
Program Cycle Characteristics Symbol Parameter t Byte Programming Time BP t Address Set-up Time AS t Address Hold Time AH t Data Set-up Time DS t Data Hold Time DH t Write Pulse Width WP t Write Pulse Width High ...
Page 12
Data Polling Characteristics Symbol Parameter t Data Hold Time Hold Time OEH ( Output Delay OE t Write Recovery Time WR Notes: 1. These parameters are characterized and not 100% tested. 2. See t ...
Page 13
Software Product Identification Entry LOAD DATA AA TO ADDRESS 555 LOAD DATA 55 TO ADDRESS AAA LOAD DATA 90 TO ADDRESS 555 ENTER PRODUCT IDENTIFICATION (2)(3)(5) MODE Software ProductIdentification Exit OR LOAD DATA AA TO ADDRESS 555 LOAD DATA 55 ...
Page 14
... AT49BV002AN-70TI 32T AT49BV002AN-70VI 32V Ordering Code Package AT49BV002AT-70JI 32J AT49BV002AT-70PI 32P6 AT49BV002AT-70TI 32T AT49BV002AT-70VI 32V Ordering Code Package AT49BV002ANT-70JI 32J AT49BV002ANT-70PI 32P6 AT49BV002ANT-70TI 32T AT49BV002ANT-70VI 32V Package Type Operation Range Industrial (- Operation Range Industrial (- Operation Range Industrial (- Operation Range Industrial (- ...
Page 15
Packaging Information 32J – PLCC 1.14(0.045) X 45˚ 0.51(0.020)MAX 45˚ MAX (3X) Notes: 1. This package conforms to JEDEC reference MS-016, Variation AE. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) ...
Page 16
PDIP A SEATING PLANE Note: 1. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). 2325 Orchard Parkway San Jose, CA 95131 R ...
Page 17
TSOP Pin 1 Identifier e E Notes: 1. This package conforms to JEDEC reference MO-142, Variation BD. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and on ...
Page 18
VSOP Pin 1 Identifier e E Notes: 1. This package conforms to JEDEC reference MO-142, Variation BA. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and on ...
Page 19
... No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. ...