W9425G6EH-5 Winbond Electronics, W9425G6EH-5 Datasheet - Page 11
![IC DDR-400 SDRAM 256MB 66TSSOPII](/photos/28/21/282152/w9425g6eh-5_sml.jpg)
W9425G6EH-5
Manufacturer Part Number
W9425G6EH-5
Description
IC DDR-400 SDRAM 256MB 66TSSOPII
Manufacturer
Winbond Electronics
Datasheet
1.W9425G6EH-5.pdf
(54 pages)
Specifications of W9425G6EH-5
Format - Memory
RAM
Memory Type
DDR SDRAM
Memory Size
256M (16Mx16)
Speed
250MHz
Interface
Parallel
Voltage - Supply
2.3 V ~ 2.7 V
Operating Temperature
0°C ~ 70°C
Package / Case
66-TSOPII
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
W9425G6EH-5
Manufacturer:
WINBOND
Quantity:
1 728
Part Number:
W9425G6EH-5
Manufacturer:
WINBOND/华邦
Quantity:
20 000
7.2.8
7.2.9
7.2.10 No-Operation Command
7.2.11 Burst Read Stop Command
7.2.12 Device Deselect Command
7.2.13 Auto Refresh Command
1) READA ≥ t
2) t
( RAS = "L", CAS = "L", WE = "L", BA0 = "L", BA1 = "L", A0 to A12 = Register Data)
The Mode Register Set command programs the values of CAS Latency, Addressing Mode, Burst
Length and DLL reset in the Mode Register. The default values in the Mode Register after power-
up are undefined, therefore this command must be issued during the power-up sequence. Also,
this command can be issued while all banks are in the idle state. Refer to the table for specific
codes.
( RAS = "L", CAS = "L", WE = "L", BA0 = "H", BA1 = "L", A0 to A12 = Register data)
The Extended Mode Register Set command can be implemented as needed for function
extensions to the standard (SDR-SDRAM). These additional functions include DLL enable/disable,
output drive strength selection. The default value of the extended mode register is not defined;
therefore this command must be issued during the power-up sequence for enabling DLL. Refer to
the table for specific codes.
( RAS = "H", CAS = "H", WE = "H")
The No-Operation command simply performs no operation (same command as Device Deselect).
( RAS = "H", CAS = "H", WE = "L")
The Burst stop command is used to stop the burst operation. This command is only valid during a
Burst Read operation.
( CS = "H")
The Device Deselect command disables the command decoder so that the RAS , CAS ,
( RAS = "L", CAS = "L", WE = "H", CKE = "H", BA0, BA1, A0 to A12 = Don’t Care)
AUTO REFRESH is used during normal operation of the DDR SDRAM and is analogous to CAS–
BEFORE–RAS (CBR) refresh in previous DRAM types. This command is non persistent, so it
must be issued each time a refresh is required.
The refresh addressing is generated by the internal refresh controller. This makes the address
bits ”Don’t Care” during an AUTO REFRESH command. The DDR SDRAM requires AUTO
WE and Address inputs are ignored. This command is similar to the No-Operation command.
Internal precharge operation begins after BL/2 cycle from Read with Auto-precharge command.
Data can be read with shortest latency, but the internal Precharge operation does not begin until
after t
This command must not be interrupted by any other command.
RCD(min)
Mode Register Set Command
Extended Mode Register Set Command
RAS (min)
≤ READA < t
RAS (min)
has completed.
- (BL/2) x t
RAS(min)
CK
- (BL/2) x t
CK
- 11 -
Publication Release Date:Dec. 03, 2008
W9425G6EH
Revision A08