XCF02SVO20C Xilinx Inc, XCF02SVO20C Datasheet - Page 27

no-image

XCF02SVO20C

Manufacturer Part Number
XCF02SVO20C
Description
IC PROM IN SYST PRG 3.3V 20TSSOP
Manufacturer
Xilinx Inc
Datasheet

Specifications of XCF02SVO20C

Programmable Type
In System Programmable
Memory Size
2Mb
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
20-TSSOP (0.173", 4.40mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
XCF02SVO20C
Manufacturer:
XILINX
Quantity:
3 276
Part Number:
XCF02SVO20C
Manufacturer:
MOT
Quantity:
50
Part Number:
XCF02SVO20C
Manufacturer:
XILINX
Quantity:
988
Part Number:
XCF02SVO20C
Manufacturer:
XILINX
0
Part Number:
XCF02SVO20C
Manufacturer:
XILINX/赛灵思
Quantity:
20 000
Part Number:
XCF02SVO20C
Manufacturer:
XILINX
Quantity:
4 469
Part Number:
XCF02SVO20C-2T
Manufacturer:
XILINX
0
Part Number:
XCF02SVO20C0100
Manufacturer:
XILINX
0
Part Number:
XCF02SVO20C0936
Manufacturer:
XILINX
0
Table 13: XCFxxP Pin Names and Descriptions (VO48/VOG48 and FS48/FSG48) (Cont’d)
DS123 (v2.18) May 19, 2010
Product Specification
CEO
EN_EXT_SEL
REV_SEL0
REV_SEL1
BUSY
CLKOUT
TMS
TCK
TDI
TDO
Pin Name
R
Scan Order
Boundary-
06
05
31
30
29
12
08
07
Output Enable
Output Enable
Mode Select
Boundary-
Function
Data Out
Data Out
Data Out
Data In
Data In
Data In
Data In
Data In
Scan
Clock
Chip Enable Output. Chip Enable Output (CEO) is connected
to the CE input of the next PROM in the chain. This output is
Low when CE is Low and OE/RESET input is High, AND the
internal address counter has been incremented beyond its
Terminal Count (TC) value or the PROM does not contain any
blocks that correspond to the selected revision. CEO returns
to High when OE/RESET goes Low or CE goes High.
Enable External Selection Input. When this pin is Low, design
revision selection is controlled by the Revision Select pins.
When this pin is High, design revision selection is controlled
by the internal programmable Revision Select control bits.
EN_EXT_SEL has an internal 50 kΩ resistive pull-up to
V
Revision Select[1:0] Inputs. When the EN_EXT_SEL is Low,
the Revision Select pins are used to select the design
revision to be enabled, overriding the internal programmable
Revision Select control bits. The Revision Select[1:0] inputs
have an internal 50 kΩ resistive pull-up to V
logic 1 to the device if the pins are not driven.
Busy Input. The BUSY input is enabled when parallel mode
is selected for configuration. When BUSY is High, the internal
address counter stops incrementing and the current data
remains on the data pins. On the first rising edge of CLK after
BUSY transitions from High to Low, the data for the next
address is driven on the data pins. When serial mode or
decompression is enabled during device programming, the
BUSY input is disabled. BUSY has an internal 50 kΩ resistive
pull-down to GND to provide a logic 0 to the device if the pin
is not driven.
Configuration Clock Output. An internal Programmable
control bit enables the CLKOUT signal, which is sourced from
either the internal oscillator or the CLK input pin. Each rising
edge of the selected clock source increments the internal
address counter if data is available, CE is Low, and
OE/RESET is High. Output data is available on the rising
edge of CLKOUT. CLKOUT is disabled if CE is High or
OE/RESET is Low. If decompression is enabled, CLKOUT is
parked High when decompressed data is not ready. When
CLKOUT is disabled, the CLKOUT pin is put into a high-Z
state. If CLKOUT is used, then it must be pulled High
externally using a 4.7 kΩ pull-up to V
JTAG Mode Select Input. The state of TMS on the rising edge
of TCK determines the state transitions at the Test Access Port
(TAP) controller. TMS has an internal 50 kΩ resistive pull-up to
V
JTAG Clock Input. This pin is the JTAG test clock. It
sequences the TAP controller and all the JTAG test and
programming electronics.
JTAG Serial Data Input. This pin is the serial input to all JTAG
instruction and data registers. TDI has an internal 50 kΩ
resistive pull-up to V
the pin is not driven.
JTAG Serial Data Output. This pin is the serial output for all
JTAG instruction and data registers. TDO has an internal
50 kΩ resistive pull-up to V
system if the pin is not driven.
CCO
CCJ
to provide a logic 1 to the device if the pin is not driven.
to provide a logic 1 to the device if the pin is not driven.
www.xilinx.com
Platform Flash In-System Programmable Configuration PROMs
CCJ
Pin Description
to provide a logic 1 to the device if
CCJ
to provide a logic 1 to the
CCO
.
CCO
to provide a
VOG48)
(VO48/
48-pin
TSOP
10
25
26
27
21
20
19
22
5
9
TFBGA
FSG48)
48-pin
(FS48/
G3
G4
G1
D2
H4
C1
C2
E2
H3
E6
27

Related parts for XCF02SVO20C