LNK563PN Power Integrations, LNK563PN Datasheet - Page 3

IC OFFLINE SWIT OTP HV 8DIP

LNK563PN

Manufacturer Part Number
LNK563PN
Description
IC OFFLINE SWIT OTP HV 8DIP
Manufacturer
Power Integrations
Series
LinkSwitch®-LPr
Datasheet

Specifications of LNK563PN

Output Isolation
Isolated
Frequency Range
77 ~ 89kHz
Voltage - Output
700V
Power (watts)
2.5W
Operating Temperature
-40°C ~ 150°C
Package / Case
8-DIP (0.300", 7.62mm), 7 Leads
Output Voltage
5.8 V
Input / Supply Voltage (max)
265 VAC
Input / Supply Voltage (min)
85 VAC
Duty Cycle (max)
70 %
Switching Frequency
83 KHz
Supply Current
220 uA
Operating Temperature Range
- 40 C to + 150 C
Mounting Style
Through Hole
For Use With
596-1128 - KIT DESIGN REF LINKSWITCH LP596-1104 - DESIGN ACCELERATOR KIT LP SWITCH
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
596-1037-5

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LNK563PN
Manufacturer:
POWER
Quantity:
15 000
Part Number:
LNK563PN
Manufacturer:
POWER
Quantity:
10 000
Part Number:
LNK563PN
Manufacturer:
POWER
Quantity:
20 000
The oscillator incorporates circuitry that introduces a small
amount of frequency jitter, typically 5% of the switching
frequency, to minimize EMI. The modulation rate of the
frequency jitter is set to 1 kHz to optimize EMI reduction
for both average and quasi-peak emissions. The frequency
jitter, which is proportional to the oscillator frequency, should
be measured with the oscilloscope triggered at the falling
edge of the DRAIN voltage waveform. The waveform in
Figure 4 illustrates the frequency jitter. The oscillator frequency
is reduced when the FB pin voltage is less than 1.69 V as
described below.
Feedback Input Circuit
The feedback input circuit at the FB pin consists of a low
impedance source follower output set at 1.69 V. When the current
delivered into this pin exceeds 70 μA, a low logic level (disable)
is generated at the output of the feedback circuit. This output
is sampled at the beginning of each cycle on the rising edge of
the clock signal. If high, the power MOSFET is turned on for
that cycle (enabled), otherwise the power MOSFET remains
off (disabled). Since the sampling is done only at the beginning
of each cycle, subsequent changes in the FB pin voltage or
current during the remainder of the cycle are ignored. When
the FB pin voltage falls below 1.69 V, the oscillator frequency
linearly reduces to typically 48% at the auto-restart threshold
voltage of 0.8 V. This function limits the power supply output
current at output voltages below the rated voltage regulation
threshold V
5.8 V Regulator and 6.3 V Shunt Voltage Clamp
The 5.8 V regulator charges the bypass capacitor connected to
the BYPASS pin to 5.8 V by drawing a current from the voltage
on the DRAIN, whenever the MOSFET is off. The BYPASS
pin is the internal supply voltage node. When the MOSFET
is on, the device runs off of the energy stored in the bypass
capacitor. Extremely low power consumption of the internal
circuitry allows LinkSwitch-LP to operate continuously from the
current drawn from the DRAIN pin. A bypass capacitor value of
0.1 μF is suffi cient for both high frequency decoupling and
energy storage.
In addition, there is a 6.3 V shunt regulator clamping the
BYPASS pin at 6.3 V when current is provided to the BYPASS
pin externally. This facilitates powering the device externally
through a resistor from the bias winding to decrease the no-
load consumption.
BYPASS Pin Undervoltage
The BYPASS pin undervoltage circuitry disables the power
MOSFET when the BYPASS pin voltage drops below 4.85 V.
Once the BYPASS pin voltage drops below 4.85 V, it must rise
back to 5.8 V to enable (turn on) the power MOSFET.
R
(see Figure 1).
Over-Temperature Protection
The thermal shutdown circuitry senses the die temperature.
The threshold is set at 142 °C typical with a 75 °C hysteresis.
When the die temperature rises above this threshold (142 °C)
the power MOSFET is disabled and remains disabled until the
die temperature falls by 75 °C, at which point the MOSFET
is re-enabled.
Current Limit
The current limit circuit senses the current in the power MOSFET.
When this current exceeds the internal threshold (I
power MOSFET is turned off for the remainder of that cycle. The
leading edge blanking circuit inhibits the current limit comparator
for a short time (t
leading edge blanking time has been set so that current spikes
caused by capacitance and rectifi er reverse recovery time will
not cause premature termination of the MOSFET conduction.
Auto Restart
In the event of a fault condition such as output short circuit or
an open loop condition, LinkSwitch-LP enters into auto-restart
operation. An internal counter clocked by the oscillator gets reset
every time the FB pin voltage exceeds the FEEDBACK Pin
Auto-Restart Threshold Voltage (V
drops below V
switching is disabled. The auto-restart alternately enables and
disables the switching of the power MOSFET at a duty cycle
of typically 12% until the fault condition is removed.
600
500
400
300
200
100
Figure 4. Frequency Jitter at f
0
0
FB(AR)
LEB
) after the power MOSFET is turned on. This
for more than 100 ms, the power MOSFET
OSC
Time (μs)
68 kHz
64 kHz
V
DRAIN
.
LNK562-564
FB(AR)
). If the FB pin voltage
LIMIT
Rev. H 11/08
), the
3
20

Related parts for LNK563PN