VIPER100A-E STMicroelectronics, VIPER100A-E Datasheet - Page 11

IC SWIT PWM SMPS CM PENTAWATT5

VIPER100A-E

Manufacturer Part Number
VIPER100A-E
Description
IC SWIT PWM SMPS CM PENTAWATT5
Manufacturer
STMicroelectronics
Series
VIPER™r
Datasheet

Specifications of VIPER100A-E

Output Isolation
Isolated
Frequency Range
90 ~ 200kHz
Voltage - Input
8 ~ 15 V
Voltage - Output
700V
Power (watts)
82W
Operating Temperature
25°C ~ 125°C
Package / Case
Pentawatt-5 HV (Bent and Staggered Leads)
Output Voltage
4.5 V
Output Current
600 uA
Output Power
82 W
Input Voltage
12.6 V to 13.4 V
Switching Frequency
200 KHz
Mounting Style
Through Hole
No. Of Pins
5
Ic Generic Number
100
Output Current Max
5.3A
Frequency
200kHz
Leaded Process Compatible
Yes
Output Current Min
3A
Rohs Compliant
Yes
Pwm Type
Current Mode PWM Controller
Number Of Pwm Outputs
1
On/off Pin
No
Adjustable Output
No
Switching Freq
90 TO 110kHz
Operating Supply Voltage (max)
15V
Synchronous Pin
No
Rise Time
50ns
Fall Time
100ns
Mounting
Through Hole
Pin Count
5 +Tab
Package Type
Pentawatt
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-4687-5

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
VIPER100A-E
Manufacturer:
ST
Quantity:
101
Part Number:
VIPER100A-E
Manufacturer:
ST
0
VIPer100A-E/ASP-E
5
5.1
5.2
Operation Description
Current Mode Topology:
The current mode control method, like the one integrated in the VIPer100A-E/ASP-E, uses two
control loops - an inner current control loop and an outer loop for voltage control. When the
Power MOSFET output transistor is on, the inductor current (primary side of the transformer) is
monitored with a SenseFET technique and converted into a voltage V
current. When V
switched off. Thus, the outer voltage control loop defines the level at which the inner loop
regulates peak current through the power switch and the primary winding of the transformer.
Excellent open loop D.C. and dynamic line regulation is ensured due to the inherent input
voltage feedforward characteristic of the current mode control. This results in improved line
regulation, instantaneous correction to line changes, and better stability for the voltage
regulation loop.
Current mode topology also ensures good limitation in case there is a short circuit. During the
first phase the output current increases slowly following the dynamic of the regulation loop.
Then it reaches the maximum limitation current internally set and finally stops because the
power supply on V
internally set can be overridden by externally limiting the voltage excursion on the COMP pin.
An integrated blanking filter inhibits the PWM comparator output for a short time after the
integrated Power MOSFET is switched on. This function prevents anomalous or premature
termination of the switching pulse in case there are current spikes caused by primary side
capacitance or secondary side rectifier reverse recovery time.
Stand-by Mode
Stand-by operation in nearly open load conditions automatically leads to a burst mode
operation allowing voltage regulation on the secondary side. The transition from normal
operation to burst mode operation happens for a power P
Where:
L
I
device is able to provide in normal operation. This current can be computed as :
t
and comparator, and represents roughly the minimum on time of the device. Note: that PSTBY
may be affected by the efficiency of the converter at low load, and must include the power
drawn on the primary auxiliary voltage.
STBY
b
P
+ t
is the primary inductance of the transformer. F
d
is the minimum controllable current, corresponding to the minimum on time that the
is the sum of the blanking time and of the propagation time of the internal current sense
P
I
STBY
STBY
S
=
=
reaches V
DD
-----------------------------
1
-- - L
2
t
b
is no longer correct. For specific applications the maximum peak current
+
P
I
L
t
2
d
p
STBY
V
IN
COMP
F
SW
(the amplified output voltage error) the power switch is
SW
is the normal switching frequency.
STBY
given by :
S
proportional to this
5 Operation Description
11/31

Related parts for VIPER100A-E