TNY278GN Power Integrations, TNY278GN Datasheet - Page 4

IC OFFLINE SWIT OVP OTP HV 8SMD

TNY278GN

Manufacturer Part Number
TNY278GN
Description
IC OFFLINE SWIT OVP OTP HV 8SMD
Manufacturer
Power Integrations
Series
TinySwitch®-IIIr
Datasheet

Specifications of TNY278GN

Output Isolation
Isolated
Frequency Range
124 ~ 140kHz
Voltage - Output
700V
Power (watts)
28W
Operating Temperature
-40°C ~ 150°C
Package / Case
8-SMD Gull Wing, 7 Leads
Output Voltage
12 V
Input / Supply Voltage (max)
265 VAC
Input / Supply Voltage (min)
85 VAC
Duty Cycle (max)
65 %
Switching Frequency
132 KHz
Supply Current
445 uA
Operating Temperature Range
- 40 C to + 150 C
Mounting Style
SMD/SMT
No. Of Outputs
1
Voltage Regulator Case Style
SMD
No. Of Pins
8
Base Number
278
Controller Type
PWM
Frequency
132kHz
Rohs Compliant
Yes
For Use With
596-1194 - KIT DESIGN REF TINYSWITCH-III
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TNY278GN
Manufacturer:
POWER
Quantity:
15 000
Company:
Part Number:
TNY278GN
Manufacturer:
POWER
Quantity:
1 444
Company:
Part Number:
TNY278GN
Manufacturer:
POWER
Quantity:
956
Company:
Part Number:
TNY278GN,,15,SOP,POWER
0
Company:
Part Number:
TNY278GN,,15,SOP,POWER
0
Company:
Part Number:
TNY278GN,,2000,SOP-7,POWER,,,2020+
0
Part Number:
TNY278GN-TL
Manufacturer:
PowerInt
Quantity:
3 000
Rev. I 01/09
Over Temperature Protection
The thermal shutdown circuitry senses the die temperature.
The threshold is typically set at 142 °C with 75 °C hysteresis.
When the die temperature rises above this threshold the power
MOSFET is disabled and remains disabled until the die
temperature falls by 75 °C, at which point it is re-enabled. A
large hysteresis of 75 °C (typical) is provided to prevent over-
heating of the PC board due to a continuous fault condition.
Current Limit
The current limit circuit senses the current in the power
MOSFET. When this current exceeds the internal threshold
(I
cycle. The current limit state machine reduces the current limit
threshold by discrete amounts under medium and light loads.
The leading edge blanking circuit inhibits the current limit
comparator for a short time (t
turned on. This leading edge blanking time has been set so that
current spikes caused by capacitance and secondary-side
rectifi er reverse recovery time will not cause premature
termination of the switching pulse.
Auto-Restart
In the event of a fault condition such as output overload, output
short circuit, or an open loop condition, TinySwitch-III enters
into auto-restart operation. An internal counter clocked by the
oscillator is reset every time the EN/UV pin is pulled low. If the
EN/UV pin is not pulled low for 64 ms, the power MOSFET
switching is normally disabled for 2.5 seconds (except in the
case of line undervoltage condition, in which case it is disabled
until the condition is removed). The auto-restart alternately
enables and disables the switching of the power MOSFET until
the fault condition is removed. Figure 5 illustrates auto-restart
circuit operation in the presence of an output short circuit.
In the event of a line undervoltage condition, the switching of
the power MOSFET is disabled beyond its normal 2.5 seconds
until the line undervoltage condition ends.
300
200
100
Figure 5.
10
LIMIT
0
5
0
4
), the power MOSFET is turned off for the remainder of that
0
Auto-Restart Operation.
TNY274-280
V
DC-OUTPUT
V
DRAIN
Time (ms)
LEB
2500
) after the power MOSFET is
5000
Adaptive Switching Cycle On-Time Extension
Adaptive switching cycle on-time extension keeps the cycle on
until current limit is reached, instead of prematurely terminating
after the DC
minimum input voltage required to maintain regulation,
extending hold-up time and minimizing the size of bulk
capacitor required. The on-time extension is disabled during the
startup of the power supply, until the power supply output
reaches regulation.
Line Undervoltage Sense Circuit
The DC line voltage can be monitored by connecting an
external resistor from the DC line to the EN/UV pin. During
power up or when the switching of the power MOSFET is
disabled in auto-restart, the current into the EN/UV pin must
exceed 25 μA to initiate switching of the power MOSFET. During
power up, this is accomplished by holding the BYPASS/MULTI-
FUNCTION pin to 4.9 V while the line undervoltage condition
exists. The BYPASS/MULTI-FUNCTION pin then rises from
4.9 V to 5.85 V when the line undervoltage condition goes
away. When the switching of the power MOSFET is disabled in
auto-restart mode and a line undervoltage condition exists, the
auto-restart counter is stopped. This stretches the disable time
beyond its normal 2.5 seconds until the line undervoltage
condition ends.
The line undervoltage circuit also detects when there is no
external resistor connected to the EN/UV pin (less than ~2 μA
into the pin). In this case the line undervoltage function is
disabled.
TinySwitch-III Operation
TinySwitch-III devices operate in the current limit mode. When
enabled, the oscillator turns the power MOSFET on at the
beginning of each cycle. The MOSFET is turned off when the
current ramps up to the current limit or when the DC
reached. Since the highest current limit level and frequency of a
TinySwitch-III design are constant, the power delivered to the
load is proportional to the primary inductance of the transformer
and peak primary current squared. Hence, designing the supply
involves calculating the primary inductance of the transformer
for the maximum output power required. If the TinySwitch-III is
appropriately chosen for the power level, the current in the
calculated inductance will ramp up to current limit before the
DC
Enable Function
TinySwitch-III senses the EN/UV pin to determine whether or
not to proceed with the next switching cycle. The sequence of
cycles is used to determine the current limit. Once a cycle is
started, it always completes the cycle (even when the EN/UV
pin changes state half way through the cycle). This operation
results in a power supply in which the output voltage ripple is
determined by the output capacitor, amount of energy per
switch cycle and the delay of the feedback.
The EN/UV pin signal is generated on the secondary by
comparing the power supply output voltage with a reference
voltage. The EN/UV pin signal is high when the power supply
output voltage is less than the reference voltage.
MAX
limit is reached.
MAX
signal goes low. This feature reduces the
www.powerint.com
MAX
limit is