MCP73833-B6I/UN Microchip Technology, MCP73833-B6I/UN Datasheet

no-image

MCP73833-B6I/UN

Manufacturer Part Number
MCP73833-B6I/UN
Description
IC LI-ION/LI-POLY CTRLR 10MSOP
Manufacturer
Microchip Technology
Datasheets

Specifications of MCP73833-B6I/UN

Function
Charge Management
Battery Type
Lithium-Ion (Li-Ion), Lithium-Polymer (Li-Pol)
Voltage - Supply
3.75 V ~ 6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
10-TFSOP (0.118", 3.00mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
• Complete Linear Charge Management Controller
• Constant Current / Constant Voltage Operation
• High Accuracy Preset Voltage Regulation:
• Programmable Charge Current: 1A Maximum
• Preconditioning of Deeply Depleted Cells
• Automatic End-of-Charge Control
• Automatic Recharge
• Two Charge Status Outputs
• Cell Temperature Monitor
• Low-Dropout Linear Regulator Mode
• Automatic Power-Down when Input Power
• Under Voltage Lockout
• Numerous Selectable Options Available for a
• Available Packages:
Applications
• Lithium-Ion / Lithium-Polymer Battery Chargers
• Personal Data Assistants
• Cellular Telephones
• Digital Cameras
• MP3 Players
• Bluetooth Headsets
• USB Chargers
© 2009 Microchip Technology Inc.
- Integrated Pass Transistor
- Integrated Current Sense
- Integrated Reverse Discharge Protection
with Thermal Regulation
- 4.2V, 4.35V, 4.4V, or 4.5V, + 0.75%
- Selectable Current Ratio
- Selectable Voltage Threshold
- Selectable Current Threshold
- Selectable Safety Time Period
- Selectable Voltage Threshold
Removed
Variety of Applications:
- Refer to Section 1.0 “Electrical
- Refer to the Product Identification System for
- DFN-10 (3 mm x 3 mm)
- MSOP-10
Characteristics” for Selectable Options
Standard Options
Stand-Alone Linear Li-Ion / Li-Polymer Charge
Management Controller
Description
The MCP73833/4 is a highly advanced linear charge
management controller for use in space-limited, cost
sensitive applications. The MCP73833/4 is available in
a 10-Lead, 3 mm x 3 mm DFN package or a 10-Lead,
MSOP package. Along with its small physical size, the
low number of external components required makes
the
applications. For applications charging from a USB
port, the MCP73833/4 can adhere to all the
specifications governing the USB power bus.
The MCP73833/4 employs a constant current/constant
voltage charge algorithm with selectable precondition-
ing and charge termination. The constant voltage
regulation is fixed with four available options: 4.20V,
4.35V, 4.40V, or 4.50V, to accomodate new, emerging
battery charging requirements. The constant current
value is set with one external resistor. The MCP73833/
4 limits the charge current based on die temperature
during high power or high ambient conditions. This
thermal regulation optimizes the charge cycle time
while maintaining device reliability.
Several options are available for the preconditioning
threshold, preconditioning current value, charge
termination value, and automatic recharge threshold.
The preconditioning value and charge termination
value are set as a ratio, or percentage, of the
programmed constant current value. Preconditioning
can be set
Characteristics” for available options and the
“Product Indentification System” for standard
options.
The MCP73833/4 is fully specified over the ambient
temperature range of -40°C to +85°C.
Package Types
MCP73833/4
DFN-10
MSOP-10
MCP73833/4
to 100%
STAT1
STAT2
V
V
V
DD
DD
SS
STAT1
STAT2
. Refer to Section 1.0 “Electrical
V
V
V
ideally
DD
DD
SS
1
2
3
4
1
2
3
4
5
5
EP
11
suited
10
9
8
7
6
DS22005B-page 1
10
9
8
7
6
V
V
THERM
PG (TE)
PROG
for
BAT
BAT
portable
V
V
THERM
PG(TE)
PROG
BAT
BAT

Related parts for MCP73833-B6I/UN

MCP73833-B6I/UN Summary of contents

Page 1

... The constant current value is set with one external resistor. The MCP73833/ 4 limits the charge current based on die temperature during high power or high ambient conditions. This thermal regulation optimizes the charge cycle time while maintaining device reliability ...

Page 2

... DS22005B-page 2 1A Li-Ion Battery Charger 1,2 9, BAT 3 8 THERM STAT1 470Ω STAT2 PROG 470Ω 470Ω MCP73833 G=0.001 1 kΩ 111 kΩ 310 kΩ 72.7 kΩ PRECONDITION + - TERMINATIO kΩ CHARG E 157.3 kΩ SHDN + Charge - Control, LDO Timer, ...

Page 3

... I 90 100 110 REG 900 1000 1100 I — 1200 — MAX MCP73833/4 (Typical)+0.3V] to 6V, T =-40°C to 85°C. A Units Conditions V Charging V Charge Complete, Standby µA Charging µA Charge Complete µA Standby (No Battery or PROG Floating) µA Shutdown (V < V ...

Page 4

... MCP73833/4 DC CHARACTERISTICS (CONTINUED) Electrical Specifications: Unless otherwise specified, all limits apply for V Typical values are at +25° (Typical)+1.0V] DD REG Parameters Preconditioning Current Regulation (Trickle Charge Constant Current Mode) Precondition Current Ratio I PREG Precondition Voltage Threshold V PTH Ratio Precondition Hysteresis Charge Termination ...

Page 5

... Symbol Min Typ Max T -40 — + -40 — +125 A T -65 — +150 A θ — 113 — JA θ — 41 — JA MCP73833/4 =-40°C to 85°C. A Units Conditions V 2.3V < V < V BAT REG V Falling DD V 2.3V < V < V BAT REG V Rising µ °C °C =-40°C to 85°C. ...

Page 6

... MCP73833/4 NOTES: DS22005B-page 6 © 2009 Microchip Technology Inc. ...

Page 7

... FIGURE 2-5: ). Supply Voltage (V A 1004 1002 1000 998 996 994 992 990 988 986 4.00 4.20 4.50 FIGURE 2-6: Supply Voltage (V MCP73833/4 = +25°C, Constant-voltage mode Programming Resistor (k:) Charge Current (I ) vs. OUT ). PROG PROG 4.75 5.00 5.25 5.50 5 ...

Page 8

... MCP73833/4 TYPICAL PERFORMANCE CURVES (Continued) Note: Unless otherwise indicated 120 100 Junction Temperature (°C) FIGURE 2-7: Charge Current (I Junction Temperature ( 1200 1000 800 600 400 200 0 Junction Temperature (°C) FIGURE 2-8: Charge Current (I Junction Temperature ( 52.0 51.5 51.0 50.5 50.0 49.5 49 ...

Page 9

... Constant-voltage mode. A 0.10 0.05 0.00 -0.05 -0.10 -0.15 -0. 4.7 µF, X7R OUT -0.25 Ceramic -0.30 Time (µs) Load Transient Response. 200 160 120 5. Time (Minutes) Complete Charge Cycle 200 160 120 80 MCP73833-FCI/ 5. 10.0 k: PROG Time (Minutes) Charge Cycle Start - DS22005B-page 9 ...

Page 10

... MCP73833/4 NOTES: DS22005B-page 10 © 2009 Microchip Technology Inc. ...

Page 11

... However, there is a diode path back to the input, and, as such, the PG output should only be pulled up to the input. The PG output is low whenever the input to the MCP73833 is above the UVLO threshold and greater than the battery voltage. © 2009 Microchip Technology Inc. ...

Page 12

... MCP73833/4 NOTES: DS22005B-page 12 © 2009 Microchip Technology Inc. ...

Page 13

... FUNCTIONAL DESCRIPTION The MCP73833 highly advanced linear charge management controller. Refer to the functional block diagram and Figure 4-1 that depicts the operational flow algorithm from charge initiation to completion and automatic recharge. SYSTEM TEST (LDO) MODE V > 100 mv) THERM DD PROG > 20 kΩ ...

Page 14

... PROG pin is opened, the MCP73833/4 enters the Standby mode where it remains until a battery is reinserted or the PROG pin is reconnected. If the input power is removed, the the MCP73833 Shutdown. When the input power is reapplied, a normal start-up sequence ensues. 4.5 Constant Voltage Mode When the voltage at the V regulation voltage, V begins ...

Page 15

... The recharge threshold is factory set. Refer to Section 1.0 “Electrical Characteristics” for recharge threshold options. 4.8 Thermal Regulation The MCP73833/4 limits the charge current based on the die temperature. The thermal regulation optimizes the charge cycle time while maintaining device reliability. Figure 4-2 depicts the thermal regulation for the MCP73833/4 ...

Page 16

... MCP73833/4 NOTES: DS22005B-page 16 © 2009 Microchip Technology Inc. ...

Page 17

... If temperature monitoring is not required, place a standard 10 kΩ resistor from THERM to V 5.1.4.1 The MCP73833/4 can be placed in a system test mode. In this mode, the MCP73833/4 operates as a low dropout linear regulator (LDO). The output voltage is regulated to the factory set voltage regulation option. ...

Page 18

... The PG output can sink current, but not source current. However, there is a diode path back to the input, and as such, the PG output should only be pulled up to the input. The PG output is low whenever the input to the MCP73833 is above the UVLO threshold and greater than the battery voltage. If the supply voltage is ...

Page 19

... APPLICATIONS The MCP73833/4 is designed to operate in conjunction with a host microcontroller or applications. The MCP73833/4 provides the preferred charge algorithm for Lithium-Ion and Lithium-Polymer C IN LED Regulated Wall Cube FIGURE 6-1: Typical Application Circuit. 5.0 4.0 3.0 2.0 MCP73833-FCI/ 1.00 k: PROG 0.0 ...

Page 20

... Alternatively, the DFN- mm) package could be utilized to reduce charge cycle times. 6.1.1.3 External Capacitors The MCP73833/4 is stable with or without a battery load. In order to maintain good AC stability in the Constant-voltage mode, a minimum capacitance of 4.7 µF is recommended to bypass the V This capacitance provides compensation when there is no battery load ...

Page 21

... Figures 6-4 and typical layout with PCB heatsinking. MCP73833 STAT1 STAT2 R PROG FIGURE 6-4: Typical Layout (Top FIGURE 6-5: Typical Layout (Bottom). © 2009 Microchip Technology Inc. and V pins, SS 6-5 depict a C OUT V BAT THERM PG V BAT MCP73833/4 DS22005B-page 21 ...

Page 22

... MCP73833/4 NOTES: DS22005B-page 22 © 2009 Microchip Technology Inc. ...

Page 23

... MCP73833-NVI/MF MCP73833-6SI/MF MCP73833-CNI/MF * Consult Factory for Alternative Device Options. 10-Lead MSOP Part Number * MCP73833-AMI/UN XXXXXX MCP73833-BZI/UN YWWNNN MCP73833-FCI/UN MCP73833-GPI/UN MCP73833-NVI/UN MCP73833-CNI/UN * Consult Factory for Alternative Device Options. Legend: XX...X Customer-specific information Y Year code (last digit of calendar year) YY Year code (last 2 digits of calendar year) WW Week code (week of January 1 is week ‘ ...

Page 24

... MCP73833/4 /HDG 3ODVWLF 'XDO )ODW 1R /HDG 3DFNDJH 0) ± 1RWH TOP VIEW 1RWHV DS22005B-page 24 PP %RG\ >')1@ BOTTOM VIEW © 2009 Microchip Technology Inc. ...

Page 25

... Microchip Technology Inc. MCP73833/4 I φ DS22005B-page 25 ...

Page 26

... MCP73833/4 NOTES: DS22005B-page 26 © 2009 Microchip Technology Inc. ...

Page 27

... Revision B (May 2009) The following is the list of modifications: 1. Added the MCP73833-6SI/MF MCP73834-6SI/MF10-lead DFN packages. 2. Updated DFN pinout. 3. Updated Package Outline Drawings. 4. Updated Appendix A Revision History. Revision A (September 2006) • Original Release of this Document. © 2009 Microchip Technology Inc. MCP73833/4 and DS22005B-page 27 ...

Page 28

... MCP73833/4 NOTES: DS22005B-page 28 © 2009 Microchip Technology Inc. ...

Page 29

... XX Device Output Temp. Package Options* Device: MCP73833: 1A Fully Integrated Charger, PG function on pin 7 MCP73833T: 1A Fully Integrated Charger, PG function on pin 7 (Tape and Reel) MCP73834: 1A Fully Integrated Charger, TE function on pin 7 MCP73834T: 1A Fully Integrated Charger, TE function on pin 7 (Tape and Reel) Output Options * * * Refer to table below for different operational options. ...

Page 30

... MCP73833/4 NOTES: DS22005B-page 30 © 2009 Microchip Technology Inc. ...

Page 31

... PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...

Page 32

... Fax: 886-3-6578-370 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2009 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 ...

Related keywords