MAX3669ETG+ Maxim Integrated Products, MAX3669ETG+ Datasheet

Page 1

... Automatic Average Power Control with Failure Monitor ♦ Complies with ANSI, ITU, and Bellcore SONET/SDH Specifications ♦ Enable Control PART MAX3669ETG MAX3669ETG+ MAX3669EHJ Applications MAX3669EHJ+ MAX3669E/D +Denotes lead-free package. Note A: Dice are designed to operate over a -40°C to +140°C junction temperature ( +25° ...

Page 2

SDH/SONET Laser Driver with Current Monitors and APC ABSOLUTE MAXIMUM RATINGS Supply Voltage, V .............................................-0.5V to +7.0V CC Current into BIAS ............................................-20mA to +150mA Current into OUT+, OUT- ............................... -20mA to +100mA Current into MD....................................................-5mA to +5mA Voltage ...

Page 3

Laser Driver with Current Monitors and APC AC ELECTRICAL CHARACTERISTICS (V = +3.14V to +5.5V, load as shown in Figure +25°C.) (Note 6) A PARAMETER SYMBOL Modulation Current Range I MOD Modulation Off-Current Modulation Current ...

Page 4

SDH/SONET Laser Driver with Current Monitors and APC (V = +3.3V +25°C, unless otherwise noted EYE DIAGRAM (622Mbps, 1300nm LASER WITH 467MHz FILTER – 1 PRBS 200ps/div MONITOR DIODE CURRENT vs. APC ...

Page 5

Laser Driver with Current Monitors and APC (V = +3.3V +25°C, unless otherwise noted DISTRIBUTION OF MODULATION CURRENT STABILITY (WORST CASE -40°C TO +85° 5mA MOD ...

Page 6

SDH/SONET Laser Driver with Current Monitors and APC PIN NAME TQFN TQFP 1, 13 17, 20 DATA DATA 11, 5, 10, 14, GND ...

Page 7

Laser Driver with Current Monitors and APC DATA+ DATA- ENABLE BIASMON MAX3669 BIAS 38 R MODMON I MOD 29 Figure 3. Functional Diagram Detailed Description The MAX3669 laser driver consists of three main parts: ...

Page 8

SDH/SONET Laser Driver with Current Monitors and APC Automatic Power Control To maintain constant average optical power, the MAX3669 incorporates an APC loop to compensate for the changes in laser threshold current over temperature and lifetime. A back-facet ...

Page 9

Laser Driver with Current Monitors and APC Resistor graph in the Typical Operating Character- istics and select the value of R BIASMAX sponds to the required current at +25°C. When using the MAX3669 in closed-loop operation, the R resistor sets ...

Page 10

SDH/SONET Laser Driver with Current Monitors and APC Calculate Power Consumption The total power dissipation of the MAX3669 can be esti- mated by the following ...

Page 11

Laser Driver with Current Monitors and APC At +5V power supply, the headroom voltage for the MAX3669 is significantly improved. In this case possible to achieve a modulation current of more than 50mA (using resistor pullups as shown ...

Page 12

SDH/SONET Laser Driver with Current Monitors and APC Chip Topography GND ENABLE GND GND N. FAIL GND N.C. N.C. GND V CC BIAS 0.070" (1.78mm) 12 ______________________________________________________________________________________ TRANSISTOR COUNT: 1525 SUBSTRATE CONNECTED TO GND V CC ...

Page 13

Laser Driver with Current Monitors and APC (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/packages.) ______________________________________________________________________________________ +3.3V, 622Mbps SDH/SONET PACKAGE OUTLINE, 32L TQFP, 5x5x1.0mm, EP ...

Page 14

SDH/SONET Laser Driver with Current Monitors and APC (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/packages.) 14 ______________________________________________________________________________________ Package Information (continued) PACKAGE OUTLINE, ...

Page 15

... Maxim product could create a situation where personal injury or death may occur. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 15 © 2005 Maxim Integrated Products +3 ...