E-L6571BD013TR STMicroelectronics, E-L6571BD013TR Datasheet
E-L6571BD013TR
Specifications of E-L6571BD013TR
Related parts for E-L6571BD013TR
E-L6571BD013TR Summary of contents
Page 1
... High voltage half bridge driver with oscillator DIP-8 can be programmed using external resistor and capacitor. The internal circuitry of the device allows driven also by external logic signal. The output drivers are designed to drive external nchannel power MOSFET and IGBT. The internal logic assures a dead time to avoid cross- conduction of the power devices ...
Page 2
... Contents Contents 1 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.3 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Oscillator frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 6 Order information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2/12 Doc ID 4946 Rev 6 L6571A - L6571B ...
Page 3
... J T Ambient temperature (Operative) amb 1. The device has an internal zener clamp between GND and VS (typical 15.6 V).Therefore the circuit should not be driven low impedance power source. Note: ESD immunity for pins 6, 7 and 8 is guaranteed up to 900 V (human body model) 1.2 Thermal data Table 2 ...
Page 4
... Oscillator timing resistor pin. A buffer set alternatively to VS and GND can provide current to the external resistor RF connected between pin 2 and 3. Alternatively, the signal on pin 2 can be used also to drive another IC (i.e. another L6569/71 to drive a full H-bridge) Oscillator timing capacitor pin. A capacitor connected between this pin and GND fixes (together with RF) the oscillating frequency Alternatively an external logic signal can be applied to the pin to drive the IC ...
Page 5
... RF low level output voltage RF OFF upper threshold CFU V CF lower threshold CFL t Internal dead time d Duty cycle, ratio between dead DC Time + conduction time of high Side and low side drivers I 1 Average current from Vs AVE f 6 Oscillation frequency out - V = 12V °C; unless otherwise specified. OUT ...
Page 6
... The device can be driven in "shut down" condition keeping the C some cares have to be taken: 1. When GND the high side driver is off and the low side The forced discharge of the oscillator capacitor C simple way to do this is to limit the current discharge with a resistive path imposing > ...
Page 7
... L6571A - L6571B Figure 5. Typical dead time vs. temperature dependency (L6571A) Figure 7. Typical frequency vs temperature dependency Figure 9. Typical and theoretical oscillator frequency vs resistor value Figure 6. Typical rise and fall times vs. load capacitance Figure 8. Quiescent current vs. supply voltage Doc ID 4946 Rev 6 Oscillator frequency 7/12 ...
Page 8
... Package mechanical data 5 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ® ECOPACK trademark. Figure 10. DIP-8 mechanical data DIM. ...
Page 9
... Table 1. SO-8 mechanical data Dim ( ddd 1. Dimensions D does not include mold flash, protru-sions or gate burrs. Mold flash, potrusions or gate burrs shall not exceed 0.15mm (.006inch) in total (both side). Figure 11. Package dimensions mm. Min Typ Max 1.35 1.75 0.10 0.25 1.10 1.65 0.33 0.51 0.19 ...
Page 10
... Order information 6 Order information Table 6. Ordering information Order codes L6571A L6571AD L6571AD013TR L6571B L6571BD L6571BD013TR 10/12 Package DIP-8 SO8 DIP-8 SO8 Doc ID 4946 Rev 6 L6571A - L6571B Packaging Tube Tape and reel Tube Tape and reel ...
Page 11
... L6571A - L6571B 7 Revision history Table 7. Document revision history Date 14-Jan-2004 15-Jan-2010 Revision 5 No history because migration 6 Updated Table 6 on page 10 Doc ID 4946 Rev 6 Revision history Changes 11/12 ...
Page 12
... The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America ...