ISO1H801G Infineon Technologies, ISO1H801G Datasheet
ISO1H801G
Specifications of ISO1H801G
Available stocks
Related parts for ISO1H801G
ISO1H801G Summary of contents
Page 1
...
Page 2
... ISO1H801G Revision History: 2009-09-16 Previous Version: V2.2 V2.0 Final Datasheet V2.1 Final Datasheet V2.2 Page 15 creepage, clearance distance and V V2.3 Diagnostic output discontinued Edition 2009-09-16 Published by Infineon Technologies AG, Am Campeon 1-12, 85579 Neubiberg, Germany Infineon Technologies AG 2009. © All Rights Reserved. ...
Page 3
... DC applications • Driver for solenoid, relays and resistive loads Description The ISO1H801G is a galvanically isolated 8 bit data interface in PG-DSO-36 package that provides 8 fully protected high-side power switches that are able to handle currents up to 625 mA bit parallel µC compatible interface allows to connect the IC directly to a µ ...
Page 4
... Datasheet Pin Configuration and Functionality Vbb N.C. 1 TAB VCC 2 DIS reserved 14 GNDCC 15 N.C. 16 N.C. 17 TAB N.C. 18 Vbb . 4 ISOFACE™ ISO1H801G 36 OUT0 35 OUT0 34 OUT1 33 OUT1 32 OUT2 31 OUT2 30 OUT3 29 OUT3 28 OUT4 27 OUT4 26 OUT5 25 OUT5 24 OUT6 23 OUT6 22 OUT7 21 OUT7 20 N.C. 19 GNDbb Version 2.3, 2009-09-16 ...
Page 5
... DIS signal, till new information is written into the input register. Current Sink to GNDCC. CS (Chip select) The system microcontroller selects the ISO1H801G by means of the low active pin CS to activate the parallel interface. By connecting the CS pin and WR pin to ground the parallel direct control is activated. Current Source to VCC ...
Page 6
... Blockdiagram Figure 2 Blockdiagram Datasheet Isolation Galvanic 6 ISOFACE™ ISO1H801G Blockdiagram Version 2.3, 2009-09-16 ...
Page 7
... Functional Description 3.1 Introduction The ISOFACE ISO1H801G includes 8 high-side power switches that are controlled by means of the integrated parallel interface. The interface is 8bit µC compatible. Furthermore a direct control mode can be selected that allows the direct control of the outputs OUT0...OUT7 by means of the inputs D0...D7 without any additional logic signal ...
Page 8
... L I L(SCp) I L(SCr) Figure 6 Turn on into short circuit, shut down by overtemperature, restart by cooling IN VOUT Normal Output short to GND operation L(SCp) Figure 7 Short circuit in on-state, shut down down by overtemperature, restart by cooling Datasheet 3 L(SCr ISOFACE™ ISO1H801G Functional Description Reserved Version 2.3, 2009-09-16 ...
Page 9
... WR have to be connected both to GNDCC. 3.5.1 Parallel Interface Signal Description CS - Chip select. The system microcontroller selects the ISO1H801G by means of the CS pin. Whenever the pin logic low state, data can be transferred from the µC. CS High to low transition: • Parallel input data can be written in from then on CS Low to high transition: • ...
Page 10
... This unit decides wether the transmitted data is valid or not. If four times serial data coming in from the internal registers is not accepted, the output stages are switched off until the next valid data is received. Datasheet t WHCS t WRPW OUT0 - OUT7 10 ISOFACE™ ISO1H801G Functional Description t CSD t on/off Version 2.3, 2009-09-16 ...
Page 11
... Loaddump = 13. 27V A V ESD V ESD 1)3) , each channel ISOFACE™ ISO1H801G Electrical Characteristics are internally galvanic isolated. bb Ω resistor in GNDbb connection. Limit Values min. max. -0.5 6 -0.5 6.5 -0.5 6.5 -0.5 6.5 -0.5 6.5 -0.5 6.5 self limited ...
Page 12
... V bb(u_rst) ∆V bb(under) I bb(uvlo) I GNDL I L(off) ) bb(off) 12 ISOFACE™ ISO1H801G Electrical Characteristics Limit Values Unit Test Condition typ. max. 1.5 K/W 50 38 Limit Values Unit Test Condition typ. max. mΩ 150 200 270 ...
Page 13
... I CC(on) Symbol min. I L(SCp) 0.7 L(SCr ON(CL bb(AZ) 2)3) T 135 jt ∆ ISOFACE™ ISO1H801G Electrical Characteristics 5.5 V 2.9 3 0 < 2. Limit Values Unit Test Condition typ. max. A 1.9 1.4 ...
Page 14
... Limit Values min. typ. WRPW CSWR WHCS CSD 14 ISOFACE™ ISO1H801G Electrical Characteristics Unit Test Condition max. 0 0.3 mV µA 170 µs 230 Unit Test Condition max. ns Version 2.3, 2009-09-16 ...
Page 15
... Note: For Qualification Report contact your local Infineon Technologies office! Datasheet Symbol min Value 500 ISO 2.6 2.6 0.01 15 ISOFACE™ ISO1H801G Electrical Characteristics Limit Values Unit Test Condition typ. max. V 1 45 1.2 Unit Conditions minute duration AC mm shortest distance through air ...
Page 16
... Datasheet Electrical Characteristics 16 ISOFACE™ ISO1H801G Version 2.3, 2009-09-16 ...
Page 17
... Datasheet Electrical Characteristics 17 ISOFACE™ ISO1H801G Version 2.3, 2009-09-16 ...
Page 18
... PG-DSO-36 Datasheet 1.1 ±0.1 15.74 ±0.1 (Heatslug) 0.65 36x +0.13 0.25 0. 45˚ 1) 15.9 ±0.1 A (Mold) 18 ISOFACE™ ISO1H801G Package Outlines ±0. 2.8 6.3 0.1 C (Mold) 14.2 ±0.3 Bottom View 13.7 -0.2 (Metal) Version 2.3, 2009-09-16 B Heatslug 0.95 ±0.15 0.25 B Heatslug ...
Page 19
... Geben Sie uns die Chance, hohe Leistung durch umfassende Qualität zu beweisen. Wir werden Sie überzeugen Published by Infineon Technologies AG Quality takes on an allencompassing significance at Semiconductor Group. bestmöglichen For us it means living up to each and every one of your demands in the best possible way ...