MC33186DH1 Freescale Semiconductor, MC33186DH1 Datasheet
MC33186DH1
Specifications of MC33186DH1
Available stocks
Related parts for MC33186DH1
MC33186DH1 Summary of contents
Page 1
... Stable Operation with an External Capacitance of Maximum 47 µF at VBAT • Pb-Free Packaging Designated by Suffix Code VW Freescale Semiconductor, Inc. reserves the right to change the detail specifications, as may be required, to permit improvements in the design of its products. © Freescale Semiconductor, Inc., 2007. All rights reserved. Device MC33186DH1/R2 MC33186VW1/R2 V PWR 33186 5 VBAT ...
Page 2
... COD Figure 2. 33186 Simplified Internal Block Diagram 33186 2 INTERNAL BLOCK DIAGRAM VBAT VBAT Internal 5V Undervoltage Overcurrent High-Side Gate Control: 1-2 Gate Control: 3-4 Overcurrent Current Limit Overtemperature Low-Side Current limitation PGND VBAT OUT1 OUT2 Analog Integrated Circuit Device Data Freescale Semiconductor ...
Page 3
... When connected to VCC, the disable Pin DI1 and DI2 are inactive. A stored failure will be reset by change of the voltage-level on IN1 or IN2. H-Bridge outputs with integrated free-wheeling diodes 14, 15 OUT1, OUT2 Analog Integrated Circuit Device Data Freescale Semiconductor PIN CONNECTIONS PIN CONNECTIONS AGND 1 NC ...
Page 4
... A filtering capacitor ( nF) can be connected between Pin 17 and Gnd. Device can operate without external capacitor, although Pin 17 decoupling capacitor help in noise reduction and allows the device to perform a maximum speed, timing and PWM frequency. 33186 4 Description Analog Integrated Circuit Device Data Freescale Semiconductor ...
Page 5
... Temperature and Moisture Sensitivity Levels (MSL www.freescale.com, search by part number [e.g. remove prefixes/suffixes and enter the core ID to view all orderable parts. (i.e. MC33xxxD enter 33xxx), and review parametrics. Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS MAXIMUM RATINGS Symbol ...
Page 6
... VINL – – U 0.7 1 200 - 80 I – 25 DI2 – – MAX 5.2 6.5 OUT 16.5 B Max Unit 4.65 V 5.0 V – mV – – V 1.4 V – V µA – µA 100 300 mΩ 7.8 A µs 26 µs 21 Analog Integrated Circuit Device Data Freescale Semiconductor ...
Page 7
... In case of overcurrent, the time when the current is greater than 7 lower than 30 µs, with a maximum frequency of 1 kHz This parameter corresponds to the time for CCP to reach its nominal value when VBAT is applied. Analog Integrated Circuit Device Data Freescale Semiconductor STATIC ELECTRICAL CHARACTERISTICS Symbol Min Typ ...
Page 8
... L = Low H = High X = High or Low Z = High impedance (all output stage transistors are switched off). 33186 8 TRUTH TABLE Input Conditions Status (8) (9) DI2 IN1 IN2 Pin names in brackets refer to coding Pin ( Outputs (10) OU1 OU2 COD VCC = ). Analog Integrated Circuit Device Data Freescale Semiconductor ...
Page 9
... VBAT Voltage Regulator INn OUn Analog Integrated Circuit Device Data Freescale Semiconductor 10k VCC IN1 IN2 DI1 DI2 COD Figure 4. Typical Application 50% 50% t DON 90% Figure 5. Output Delay Time ELECTRICAL CHARACTERISTICS 47µF Ccp=33nF Power Ground VBAT SF CP OUT1 M OUT2 GND Power Ground ...
Page 10
... ELECTRICAL CHARACTERISTICS DIn OUn OUn 33186 10 50% t DDIS 10% Figure 6. Disable Delay Time 90% 10% tf Figure 7. Output Switching Time Z 90% 10% tr Analog Integrated Circuit Device Data Freescale Semiconductor ...
Page 11
... Load- current > 8A TYP 6.5A Control signal Status Flag Detail A 6. switch-off time in current limitation current limitation blanking time B Analog Integrated Circuit Device Data Freescale Semiconductor A Overcurrent detection Figure 8. Current Limitation on Low Side ELECTRICAL CHARACTERISTICS Overturned 33186 11 ...
Page 12
... Figure 13. Vcp vs. Battery Voltage 200 VBAT=5V without Ccp 190 180 170 160 150 140 130 120 75 100 125 110 -50 Figure 14. RDSON vs. Temperature - 100 T, TEMPERATURE (°C) Temperature BATTERY VOLTAGE (V) - 100 T, TEMPERATURE (°C) Analog Integrated Circuit Device Data Freescale Semiconductor 125 35 125 ...
Page 13
... T, TEMPERATURE (°C) Figure 16. Overcurrent Detection vs. Temperature Imotor (1A/div) Figure 17. Current Limitation Analog Integrated Circuit Device Data Freescale Semiconductor 75 100 125 75 100 125 Figure 19. Output Switching Time: Tr I(out) max= 7A Figure 20. Output Switching Time: Tf ELECTRICAL CHARACTERISTICS ta=20.5µs Imotor (1A/div) ...
Page 14
... I OUT2 (A) Note: Current through internal recirculation diode, @125°C in case of negative voltage at OUT2 Figure 25. Maximum Di2 Input Current vs. Iout2, current Analog Integrated Circuit Device Data Freescale Semiconductor Iochs= 16A ...
Page 15
... We characterized the 20 HSOP on a double side PCB. The bottom side area of the copper is 7 surface is 2 see Figure 26. Top Side Bottom Side Figure 26. PCB Test Layout Analog Integrated Circuit Device Data Freescale Semiconductor PACKAGING SOLDERING 100 The top Rth (°C/W) 1 0,1 0,001 0,01 Figure 27 ...
Page 16
... E1 10.900 11.100 E2 2.500 2.700 E3 6.400 7.200 E4 2.700 2.900 L 0.840 1.100 L1 0.350 BSC b 0.400 0.520 b1 0.400 0.482 c 0.230 0.320 c1 0.230 0.280 e 1.270 BSC h ––– 1.100 0 8 aaa 0.200 bbb 0.100 DATE 07/22/98 Analog Integrated Circuit Device Data Freescale Semiconductor ...
Page 17
... Single layer thermal test board per JEDEC JESD51-3 and JESD51-5. 5. Thermal resistance between the die junction and the exposed pad surface; cold plate attached to the package bottom side, remaining surfaces insulated. Analog Integrated Circuit Device Data Freescale Semiconductor ), and thermal θJA [°C/ ...
Page 18
... Natural convection, still air 33186 18 NC IN2 DI1 CP VBAT OUT2 OUT2 DI2 PGND PGND Figure 29. Thermal Test Board Table 6. Thermal Resistance Performance A [ the thermal resistance between die junction and θJA ambient air [°C/W] θ 300 49 600 47 Analog Integrated Circuit Device Data Freescale Semiconductor ...
Page 19
... Figure 30. Device on Thermal Test Board R 100 100 0.1 0.1 1.00E-03 1.00E-02 1.00E-03 1.00E- Step Response, Device on Thermal Test Board Area A = 600 (mm Analog Integrated Circuit Device Data Freescale Semiconductor x R [°C/W] θJA 0 300 0 300 2 Heat Spreading Area A [mm ] Heat spreading area A [mm²] 1.00E-01 1.00E+00 1 ...
Page 20
... Updated data sheet formal 10/2006 6.0 • Removed Peak Package Reflow Temperature During Reflow (solder reflow) parameter from MAXIMUM RATINGS on page www.freescale.com. 33186 20 REVISION HISTORY 5. Added note with instructions to obtain this information from Analog Integrated Circuit Device Data Freescale Semiconductor ...
Page 21
... Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer ...