BD6232FP-E2 Rohm Semiconductor, BD6232FP-E2 Datasheet

Page 1

For brush motors H-bridge drivers (36V max.) BD6230, BD6231, BD6232, BD6235, BD6236, BD6237  Overview These H-bridge drivers are full bridge drivers for brush motor applications. Each IC can operate at a wide range of power supply voltages (from 3V ...

Page 2

BD6230, BD6231, BD6232, BD6235, BD6236, BD6237  Absolute maximum ratings (Ta=25°C, All voltages are with respect to ground) Parameter Symbol Supply voltage VCC Output current I OMAX All other input pins V IN Operating temperature T OPR Storage temperature T ...

Page 3

BD6230, BD6231, BD6232, BD6235, BD6236, BD6237  Electrical characteristic curves (Reference data) 2.5 2.0 1.5 85°C 1.0 25°C -40°C 0 Supply Voltage: Vcc [V] Fig.1 Supply current (1ch) 1.0 85°C 25°C 0.8 -40°C 0.6 0.4 ...

Page 4

BD6230, BD6231, BD6232, BD6235, BD6236, BD6237  Electrical characteristic curves (Reference data) - Continued 0.8 85°C 25°C -40°C 0.6 0.4 0 0.1 0.2 0.3 0.4 Output Current: IOUT [A] Fig.13 Output high voltage (0.5A class) 2 -40°C 25°C ...

Page 5

BD6230, BD6231, BD6232, BD6235, BD6236, BD6237  Block diagram and pin configuration BD6230F / BD6231F VREF 6 DUTY PROTECT FIN 4 CTRL RIN 5 1 OUT1 Fig.25 BD6230F / BD6231F OUT1 GND VCC OUT2 VCC VREF FIN RIN Fig.26 SOP8 ...

Page 6

... FIN Note: All pins not described above are NC pins. Note: Use all VCC pin by the same voltage. 6/16 Technical Note Table 3 BD6232FP Name Function OUT1 Driver output GND Small signal ground RNF Power stage ground OUT2 Driver output VREF Duty setting pin ...

Page 7

BD6230, BD6231, BD6232, BD6235, BD6236, BD6237  Block diagram and pin configuration - Continued BD6236FM VREFA 9 DUTY PROTECT FINA 11 CTRL RINA 10 GND 22 VREFB 23 DUTY PROTECT FINB 25 CTRL RINB 24 GND 8 FIN GND Fig.33 ...

Page 8

BD6230, BD6231, BD6232, BD6235, BD6236, BD6237  Block diagram and pin configuration - Continued BD6237FM VREFA 9 DUTY PROTECT FINA 11 CTRL RINA 10 GND 22 VREFB 23 DUTY PROTECT FINB 25 CTRL RINB 24 GND 8 FIN GND Fig.35 ...

Page 9

BD6230, BD6231, BD6232, BD6235, BD6236, BD6237  Functional descriptions 1) Operation modes FIN RIN PWM PWM g H PWM h PWM ...

Page 10

BD6230, BD6231, BD6232, BD6235, BD6236, BD6237 e) f) PWM control mode A The rotational speed of the motor can be controlled by the switching duty when the PWM signal is input to the FIN pin or the RIN pin. In ...

Page 11

BD6230, BD6231, BD6232, BD6235, BD6236, BD6237 i) j) VREF control mode The built-in VREF-switching on duty conversion circuit provides switching duty corresponding to the voltage of the VREF pin and the VCC voltage. The function offers the same level of ...

Page 12

BD6230, BD6231, BD6232, BD6235, BD6236, BD6237 c) Thermal shutdown (TSD) circuit The TSD circuit operates when the junction temperature of the driver exceeds the preset temperature (175°C nominal). At this time, the controller forces all driver outputs to high impedance. ...

Page 13

BD6230, BD6231, BD6232, BD6235, BD6236, BD6237  Notes for use 1) Absolute maximum ratings Devices may be destroyed when supply voltage or operating temperature exceeds the absolute maximum rating. Because the cause of this damage cannot be identified as, for ...

Page 14

BD6230, BD6231, BD6232, BD6235, BD6236, BD6237 11) Testing on application boards When testing the application board, connecting a capacitor to a low impedance pin subjects the IC to stress. Therefore, always discharge capacitors after each process or ...

Page 15

BD6230, BD6231, BD6232, BD6235, BD6236, BD6237 SOP8 <Dimension> HSOP25 <Dimension> 13.6 ± 0.2 2.75 ± 0 0.25 ± 0.1 1.95 ± 0.1 0.8 0.1 0.36 ± 0.1 HSOP-M28 <Dimension> 18.5 ± 0 ...

Page 16

BD6230, BD6231, BD6232, BD6235, BD6236, BD6237 www.rohm.com ○ 2009 ROHM Co., Ltd. All rights reserved. c 16/16 Technical Note 2009.08 - Rev.C ...

Page 17

No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose ...