TLE7185E Infineon Technologies, TLE7185E Datasheet
TLE7185E
Specifications of TLE7185E
TLE7185E
TLE7185ETR
Available stocks
Related parts for TLE7185E
TLE7185E Summary of contents
Page 1
...
Page 2
Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
Bridge Driver IC 1 Overview Features • Drives 6 N-Channel Power MOSFETs • Separate control input for each MOSFET • Separate Source pin for each MOSFET • Integrated charge pump for operation at low battery voltages • Adjustable dead ...
Page 4
Block Diagram ____ ERR1 ____ Diagnostic logic ERR2 Under voltage Over voltage ENA Short circuit SCDL STOE DT IL1 Input control ___ IH1 Shoot through protection / IL2 ___ IH2 IL3 ___ IH3 temperature Figure 1 Block Diagram Data ...
Page 5
Pin Configuration 3.1 Pin Assignment TLE7185-1E STOE ERR2 ERR1 ENA IH1 IL1 IH2 IL2 IH3 IL3 DT INH GND CB GND Figure 2 Pin Configuration Data Sheet ...
Page 6
Pin Definitions and Functions Pin Symbol Function 1 STOE Input pin to enable shoot through option in all 3 half bridges (active high) 2 ERR2 Open drain error output 2 3 ERR1 Open drain error output 1 4 ENA ...
Page 7
General Product Characteristics 4.1 Absolute Maximum Ratings 1) Absolute Maximum Ratings T 40 °C ≤ ≤ 150 °C ; all voltages with respect to ground, positive current flowing into pin (unless otherwise specified) j Pos. Parameter Voltages 4.1.1 Supply ...
Page 8
Absolute Maximum Ratings (cont’ °C ≤ ≤ 150 °C ; all voltages with respect to ground, positive current flowing into pin (unless otherwise specified) j Pos. Parameter 2) 4.1.28 ESD Resistivity 3) 4.1.29 CDM 1) Not subject to ...
Page 9
Thermal Resistance Note: This thermal data was generated in accordance with JEDEC JESD51 standards. For more information www.jedec.org. Pos. Parameter 1) 4.3.1 Junction to Case 1) 4.3.2 Junction to Ambient 1) Not subject to production test, specified ...
Page 10
Description and Electrical Characteristics 5.1 MOSFET Driver 5.1.1 Output Stages The 3 low side and 3 high side powerful push-pull output stages of the TLE7185-1E are all floating blocks, each with its own source pin. This allows the direct ...
Page 11
MOSFETs, increasing their the associated power dissipation. The TLE7185-1E has a charge pump circuitry for external capacitors. The operation of the charge pump is independent upon ...
Page 12
Electrical Characteristics MOSFET drivers 5.5 to 32V, = -40 to +150°C all voltages with respect to ground, positive current flowing into pin S j (unless otherwise specified) Pos. Parameter 5.1.5 ILx; ENA; STOE pull down resistors 5.1.6 ...
Page 13
Electrical Characteristics MOSFET drivers 5.5 to 32V, = -40 to +150°C all voltages with respect to ground, positive current flowing into pin S j (unless otherwise specified) Pos. Parameter Wake up / Inhibit 5.1.28 INH propagation time ...
Page 14
Protection and Diagnostic Functions 5.2.1 Short Circuit Protection The TLE7185-1E provides a short circuit protection for the external MOSFETs monitoring of the drain- source voltage of the external MOSFETs. As soon as this voltage is higher ...
Page 15
Shoot Through Option The TLE7185-1E offers the possibility to switch off the Shoot Through Protection by setting the STOE pin to high and in the same time all IHX to low and all ILX to high. Only if all ...
Page 16
... During disable (ENA = low) any error is shown. However, the Short circuit detection error is reset (error is cleared) and can not reoccur as the output stages which drive the external MOSFETs are disabled. In case of under voltage lockout, the ERR pins deviate from the table above as the charge pump is not active and the TLE7185E is not biased properly. Data Sheet 5V ...
Page 17
Electrical Characteristics Electrical Characteristics - Protection and diagnostic functions 5.5 to 32V, = -40 to +150°C, all voltages with respect to ground, positive current flowing into pin S j (unless otherwise specified) Pos. Parameter ERR pins ...
Page 18
Electrical Characteristics - Protection and diagnostic functions 5.5 to 32V, = -40 to +150°C, all voltages with respect to ground, positive current flowing into pin S j (unless otherwise specified) Pos. Parameter Reset and Enable 5.2.25 Reset ...
Page 19
... GH1 R GH1 SH1 C BH2 BS2 470nF CL GH2 R GH2 CH SH2 C BH3 BS3 470nF GH3 ERR2 R GH3 SH3 ERR1 TLE7185E GL1 STOE R GL1 SL1 ENA IL1 GL2 IH1 IL2 SL2 IH2 IL3 GL3 IH3 SL3 SCDL DT GND DT GND 19 TLE7185-1E Application Description KL 15 ...
Page 20
Package Outlines 0. 0.65 = 11.05 2) 0.33 ±0.08 0. 12.8 -0.2 Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Does not ...
Page 21
Revision History Version Date Changes Rev. 2.4 2010-07-16 Change of Name and Marking Rev. 2.3 2009-08-18 Parameter Rev. 2.2 2009-01-13 chapter 7: package outline updated (Stand-off reduced) parameter 5.1.20 R Rev. 2.1 2008-10-08 Data Sheet Chapter 5.1.8 High level ...
Page 22
Data Sheet 22 TLE7185-1E Revision History Rev. 2.4, 2010-07-16 ...
Page 23
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...