MC33262PG ON Semiconductor, MC33262PG Datasheet - Page 8

• Manufacturer Part Number: MC33262PG
• Description: IC PFC CONTROLLER CRM 8DIP
• Manufacturer: ON Semiconductor

Specifications of MC33262PG

• Mode: Critical Conduction (CRM)
• Current - Startup: 250µA
• Voltage - Supply: 12 V ~ 28 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Maximum Operating Temperature: + 105 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Frequency - Switching: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: MC33262PGOS

attained by forcing the preconverter to switch as the ac line
voltage crosses through zero. The forced switching is
achieved by adding a controlled amount of offset to the
Multiplier and Current Sense Comparator circuits. The
equation shown below accounts for the built- - in offsets and
is accurate to within ten percent. Let V
Zero Current Detector
mode controller, whereby output switch conduction is
initiated by the Zero Current Detector and terminated when
the peak inductor current reaches the threshold level
established by the Multiplier output. The Zero Current
Detector initiates the next on- - time by setting the RS Latch
at the instant the inductor current reaches zero. This critical
conduction mode of operation has two significant benefits.
First, since the MOSFET cannot turn- - on until the inductor
current reaches zero, the output rectifier reverse recovery
time becomes less critical, allowing the use of an
inexpensive rectifier. Second, since there are no deadtime
gaps between cycles, the ac line current is continuous, thus
limiting the peak switch to twice the average input current.
current by monitoring when the auxiliary winding voltage
falls below 1.4 V. To prevent false tripping, 200 mV of
hysteresis is provided. Figure 9 shows that the thresholds
are well- - defined over temperature. The Zero Current
Detector input is internally protected by two clamps. The
upper 6.7 V clamp prevents input overvoltage breakdown
while the lower 0.7 V clamp prevents substrate injection.
Current limit protection of the lower clamp transistor is
provided in the event that the input pin is accidentally
shorted to ground. The Zero Current Detector input to
Drive Output turn- - on propagation delay is typically 320 ns.
MOSFET
A significant reduction in line current distortion can be
The MC34262 operates as a critical conduction current
The Zero Current Detector indirectly senses the inductor
Inductor Current
Q1
V
CS
On
Off
0
Figure 19. Inductor Current and MOSFET
, Pin 4 Threshold = 0.544 (V
Gate Voltage Waveforms
+ 0.0417 (V
Peak
Pin 2
-- V
Pin 2
th(M)
th(M)
-- V
)
th(M)
= 1.991 V
) V
Average
Pin 3
http://onsemi.com
8
Current Sense Comparator and RS Latch
used ensures that only a single pulse appears at the Drive
Output during a given cycle. The inductor current is
converted to a voltage by inserting a ground- - referenced
sense resistor R
Q1. This voltage is monitored by the Current Sense Input
and compared to a level derived from the Multiplier output.
The peak inductor current under normal operating
conditions is controlled by the threshold voltage of Pin 4
where:
preconverter startup at extremely high line or if output
voltage sensing is lost. Under these conditions, the
Multiplier output and Current Sense threshold will be
internally clamped to 1.5 V. Therefore, the maximum peak
switch current is limited to:
high frequency noise that may be present on the current
waveform. This filter helps reduce the ac line current
distortion especially near the zero crossings. With the
component values shown in Figure 20, the Current Sense
Comparator threshold, at the peak of the haversine varies
from 1.1 V at 90 Vac to 100 mV at 268 Vac. The Current
Sense Input to Drive Output turn- - off propagation delay is
typically less than 200 ns.
Timer
eliminate the need for an external oscillator when used in
stand- - alone applications. The Timer provides a means to
automatically start or restart the preconverter if the Drive
Output has been off for more than 620 ms after the inductor
current reaches zero. The restart time delay versus
temperature is shown in Figure 8.
Undervoltage Lockout and Quickstart
incorporated to guarantee that the IC is fully functional
before enabling the output stage. The positive power
supply terminal (V
comparator with the upper threshold set at 13 V and the
lower threshold at 8.0 V. In the stand- - by mode, with V
at 7.0 V, the required supply current is less than 0.4 mA.
This large hysteresis and low startup current allow the
implementation of efficient bootstrap startup techniques,
making these devices ideally suited for wide input range
off- - line preconverter applications. An internal 36 V
clamp has been added from V
and capacitor C
feature is desirable if external circuitry is used to delay the
startup of the preconverter. The supply current, startup, and
operating voltage characteristics are shown in Figures 13
and 14.
The Current Sense Comparator RS Latch configuration
Abnormal
An internal RC filter has been included to attenuate any
A watchdog timer function was added to the IC to
An Undervoltage Lockout comparator has been
I
7
operating
L(pk
4
in series with the source of output switch
from an overvoltage condition. This
I
) =
pk(max)
CC
) is monitored by the UVLO
Pin 4 Threshold
=
conditions
CC
to ground to protect the IC
1.5 V
R
R
7
7
occur
during
CC