MAX8513EEI+ Maxim Integrated Products, MAX8513EEI+ Datasheet

IC SUPPLY TRPL W/MON 28QSOP

MAX8513EEI+

Manufacturer Part Number
MAX8513EEI+
Description
IC SUPPLY TRPL W/MON 28QSOP
Manufacturer
Maxim Integrated Products
Type
Step-Down (Buck)r
Datasheet

Specifications of MAX8513EEI+

Internal Switch(s)
No
Synchronous Rectifier
No
Number Of Outputs
3
Voltage - Output
1.25 ~ 5.5 V
Current - Output
40mA
Frequency - Switching
300kHz ~ 1.4MHz
Voltage - Input
4.5 ~ 28 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
28-QSOP
Power - Output
860mW
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
The MAX8513/MAX8514 integrate a voltage-mode
PWM step-down DC-DC controller and two LDO con-
trollers, a voltage monitor, and a power-on reset for the
lowest-cost power-supply and monitoring solution for
xDSL modems, routers, gateways, and set-top boxes.
The DC-DC controller switching frequency can be set
with an external resistor from 300kHz to 1.4MHz, to allow
for the optimization of cost, size, and efficiency. For noise-
sensitive applications, the DC-DC controller can also be
synchronized to an external clock, minimizing noise inter-
ference. Operation above 1.1MHz reduces noise for high
data-rate xDSL applications. An adjustable soft-start and
adjustable foldback current limit provide reliable startup
and fault protection. The DC-DC controller output voltage
can be set externally to a voltage from 1.25V to 5.5V.
Current limiting is accomplished by inductor current sens-
ing for improved efficiency, or by an external sense resis-
tor for better accuracy.
The MAX8513/MAX8514s’ first LDO controller is
designed to provide a low-cost, high-current regulated
output from 0.8V to 5.5V using an N-channel MOSFET or
a low-current output using a low-cost NPN transistor. The
MAX8513’s second regulator can be used to generate
0.8V to 27V output with a low-cost PNP transistor. Both
LDO regulators can operate either from the DC-DC con-
troller output or from a higher voltage derived with a fly-
back overwinding on the DC-DC converter inductor. The
MAX8514’s second LDO regulator is designed to pro-
vide a negative output with an NPN transistor.
A sequence input allows the outputs to either power up
together, or for the DC-DC regulator to power up first
and each LDO controller to power up in sequence. An
input power-fail output (PFO) is provided for input
power-fail warning, such as in dying-gasp applications.
A power-on reset circuit with a 140ms delay is also
included to indicate when all outputs have achieved
regulation and stabilized.
19-3178; Rev 0; 2/04
Pin Configurations appear at end of data sheet.
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
Wide-Input, High-Frequency, Triple-Output Supplies
xDSL, Cable, ISDN Modems, and Routers
Wireless Routers
Set-Top Boxes
Automotive Dashboard Electronics
________________________________________________________________ Maxim Integrated Products
with Voltage Monitor and Power-On Reset
General Description
Applications
♦ Low-Cost DC-DC Controller with Two LDOs
♦ Wide Input Range: 4.5V to 28V
♦ 300kHz to 1.4MHz Adjustable Switching
♦ Low Noise for High Data-Rate xDSL Applications
♦ Synchronizable to External Clock
♦ Adjustable Soft-Start
♦ Lossless Adjustable Foldback Current Limit
♦ Power-On Reset with 140ms Delay
♦ Adjustable Input Power-Fail Warning for Dying
♦ Selectable Output-Voltage Sequencing or
POWER-ON RESET
MAX8513EEI
MAX8514EEI
MAX8514AEI
Frequency
Gasp
Output-Voltage Tracking
INPUT POWER-
FAIL MONITOR
(4.5V TO 28V)
PART
OFF
OUTPUT
SYNC
ON
V
IN
-40 C to +85 C
-40 C to +85 C
-40 C to +125 C
CONTROLLER 1
CONTROLLER 2
TEMP RANGE
CONTROLLER
MAX8513
STEP-
DOWN
Ordering Information
LDO
LDO
Functional Diagram
PIN-PACKAGE
28 QSOP
28 QSOP
28 QSOP
Features
V
(1.25V TO 5.5V)
OUT1
V
(0.8V TO V
V
(0.8V TO 27V)
OUT2
OUT3
OUT1
)
1

Related parts for MAX8513EEI+

MAX8513EEI+ Summary of contents

Page 1

... Wireless Routers Set-Top Boxes Automotive Dashboard Electronics Pin Configurations appear at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. ♦ Low-Cost DC-DC Controller with Two LDOs ♦ Wide Input Range: 4.5V to 28V ♦ ...

Page 2

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset ABSOLUTE MAXIMUM RATINGS IN, DRV3P, SUP2 to GND.......................................-0.3V to +30V DRV2 to GND ..........................................-0. DRV3N to GND......................(V - 28V SUP3N FREQ, PFI, PFO, POR, SUP3N, SYNC/EN, ...

Page 3

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset ELECTRICAL CHARACTERISTICS (continued 12V SUP2 PVL BST 15.0kΩ 0°C to +85°C, unless otherwise noted. Typical values are ...

Page 4

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset ELECTRICAL CHARACTERISTICS (continued 12V SUP2 PVL BST 15.0kΩ 0°C to +85°C, unless otherwise noted. Typical values are ...

Page 5

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset ELECTRICAL CHARACTERISTICS (continued 12V SUP2 PVL BST 15.0kΩ 0°C to +85°C, unless otherwise noted. Typical values are ...

Page 6

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset ELECTRICAL CHARACTERISTICS (continued 12V SUP2 PVL BST 15.0kΩ -40°C to +125°C (Note 2), unless otherwise noted.) A ...

Page 7

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset ELECTRICAL CHARACTERISTICS (continued 12V SUP2 PVL BST 15.0kΩ -40°C to +125°C (Note 2), unless otherwise noted.) A ...

Page 8

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset ELECTRICAL CHARACTERISTICS (continued 12V SUP2 PVL BST 15.0kΩ -40°C to +125°C (Note 2), unless otherwise noted.) A ...

Page 9

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset (Circuit of MAX8513 evaluation kit EFFICIENCY vs. INPUT VOLTAGE 100 3.3V OUT1 OUT1 ...

Page 10

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset (Circuit of MAX8513 evaluation kit 12V OUTPUT1 LOAD-TRANSIENT RESPONSE I = 0.75A 25mA OUT2 OUT3 50mV/div 50mV/div 100mV/div 0A 40µs/div SWITCHING WAVEFORMS (ALL OUTPUTS ...

Page 11

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset (Circuit of MAX8513 evaluation kit STAGGERED SEQUENCE (SEQ = GND 2ms/div OUTPUT1 SHORT CIRCUIT (ALL OUTPUTS AT FULL LOAD 20µs/div ______________________________________________________________________________________ Typical Operating ...

Page 12

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset PIN MAX8513 MAX8514 NAME Power-Fail Input. Connect PFI to an external resistive-divider between IN, PFI, and GND. PFI 1 1 PFI senses V 20mV of hysteresis. PFO 2 2 Power-Fail ...

Page 13

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset PIN MAX8513 MAX8514 NAME SEQ 18 18 SYNC/ N.C. 20 — SUP3N — 20 DRV3P 21 — DRV3N — POR 23 23 FB3P 24 ...

Page 14

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset SS SYNC/EN VL BIAS GND FREQ SEQ PFI PFO N POR N REF MAX8513 Figure 1. MAX8513 Functional Diagram 14 ______________________________________________________________________________________ 1/7.5 5µA PWM COMP. 1V P-P ...

Page 15

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset SS SYNC/EN VL BIAS GND FREQ SEQ PFI PFO N POR N REF MAX8514 Figure 2. MAX8514 Functional Diagram ______________________________________________________________________________________ 1/7.5 5µA PWM COMP. 1V P-P ERROR ...

Page 16

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset Detailed Description The MAX8513/MAX8514 combine a step-down DC-DC converter and two LDOs, providing three output volt- ages for xDSL modem and set-top box applications. The switching frequency is set with ...

Page 17

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset Internal 5V Linear Regulator All MAX8513/MAX8514 functions (except for the posi- tive output LDO with an NFET or NPN, and the negative LDO on the MAX8514) are powered from the ...

Page 18

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset Thermal-Overload Protection Thermal-overload protection limits the total power dissi- pation in the MAX8513/MAX8514. When the junction temperature exceeds T = +170°C, a thermal sensor J shuts down the device, forcing ...

Page 19

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset diode on the secondary side (Q2 and D2 in the Typical Applications Circuits). n and n 2 turns of the secondary winding and the primary wind- ing, respectively ...

Page 20

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset The peak-to-peak output voltage ripple as a conse- quence of the ESR, ESL, and output capacitance is × RIPPLE ESR ( ) ...

Page 21

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset × I × f × OUT 1 S where I is the average DH high driver output-cur- GATE rent capability determined by: 2 ...

Page 22

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset To set the current limit and the current-limit foldback thresholds, first select the foldback current-limit ratio (P ). This ratio is the foldback current limit (I FB divided by the ...

Page 23

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset When the output capacitance is comprised of parallel- ing n number of identical capacitors whose values are C with ESR then: EACH ESR_EACH × ...

Page 24

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset This gain is also set by the ratio of R3/R1 where R1 is calculated in the OUT1 Voltage Setting section. Thus × ...

Page 25

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset Use 6.8kΩ π × × π × Ω PMOD Use 4.7nF × ...

Page 26

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset This gain between f and f is also set by the ratio R3/R1, where R1 is selected in the OUT1 Voltage Setting section. Therefore × ...

Page 27

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset π × × × π × × ...

Page 28

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset A third pole occurs due to the input capacitance of the NMOS transistor’s gate iss data sheet), and the compensation resistor (R NPN bipolar transistor is used ...

Page 29

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset the package’s power dissipation could limit the useable maximum input-to-output voltage differential. The maximum power-dissipation capability of the tran- sistor’s package and mounting must allow the actual power dissipation in ...

Page 30

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset POLE π × the second pole occurs well after unity-gain crossover, the linear regulator remains ...

Page 31

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset V IN C10 2.2µ R10 68.1kΩ SUP2 PFI R11 12.4kΩ EN/SYNC C5 R3 4.7nF 6.8kΩ FB1 COMP1 C12 33pF R7 10.7kΩ FREQ IC1 MAX8513 REF C9 0.1µF GND ...

Page 32

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset 16V R15 10Ω C10 2.2µ R10 68.1kΩ SUP2 PFI R11 12.4kΩ EN/SYNC C5 R3 4.7nF 6.8kΩ FB1 COMP1 C12 33pF R7 10.7kΩ FREQ IC1 ...

Page 33

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset MAX8513 a) POSITIVE OUTPUT VOLTAGE MAX8514 b) NEGATIVE OUTPUT VOLTAGE Figure 7. Base-Drive Noise Reduction Applications Information PC Board Layout Guidelines Careful PC board layout is critical to achieve low ...

Page 34

Wide-Input, High-Frequency, Triple-Output Supplies with Voltage Monitor and Power-On Reset TOP VIEW PFI 1 PFO BST 5 MAX8513 DL 6 PVL 7 PGND COMP1 10 FB1 11 FREQ 12 REF 13 GND ...

Page 35

... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 35 © 2004 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products ...

Related keywords