ACPL-W302-500E Avago Technologies US Inc., ACPL-W302-500E Datasheet - Page 7
![OPTOCOUPLER IGBT 0.4A 6-SOIC](/photos/15/83/158366/acpl-w302_wht_sml.jpg)
ACPL-W302-500E
Manufacturer Part Number
ACPL-W302-500E
Description
OPTOCOUPLER IGBT 0.4A 6-SOIC
Manufacturer
Avago Technologies US Inc.
Specifications of ACPL-W302-500E
Output Type
Push-Pull, Totem-Pole
Package / Case
6-SOP
Voltage - Isolation
3750Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
400mA
Propagation Delay High - Low @ If
300ns @ 7mA
Current - Dc Forward (if)
25mA
Input Type
DC
Mounting Type
Surface Mount
Fall Time
50 ns
Rise Time
50 ns
Configuration
1 Channel
Isolation Voltage
3750 Vrms
Maximum Propagation Delay Time
700 ns
Maximum Forward Diode Voltage
1.8 V
Minimum Forward Diode Voltage
1.2 V
Maximum Reverse Diode Voltage
5 V
Maximum Forward Diode Current
12 mA
Maximum Power Dissipation
250 mW
Maximum Operating Temperature
+ 100 C
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Table 7. Package Characteristics
Notes:
1. Derate linearly above 70°C free air temperature at a rate of 0.3 mA/°C.
2. Maximum pulse width = 10 Ps, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with I
3. Derate linearly above 85°C, free air temperature at the rate of 4.0 mW/°C.
4. Input power dissipation does not require derating.
5. Maximum pulse width = 50 Ps, maximum duty cycle = 0.5%.
6. In this test, V
7. Maximum pulse width = 1 ms, maximum duty cycle = 20%.
8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 4500 V
9. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 Vrms for 1 second (leakage detection
10. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together.
11. PDD is the difference between t
12. Common mode transient immunity in the high state is the maximum tolerable |dV
13. Common mode transient immunity in a low state is the maximum tolerable |dV
14. This load condition approximates the gate load of a 1200 V/20 A IGBT.
15. The power supply current increases when operating frequency and Q
7
Parameter
Input-Output Momentary
Withstand Voltage
Input-Output Resistance
Input-Output Capacitance
minimum = 0.2 A. See Application section for additional details on limiting I
current limit I
Insulation Characteristics Table, if applicable.
current limit II-O < 5 A). This test is performed before 100% production test for partial discharge (method B) shown in the IEC/EN/DIN EN 60747-5-2
Insulation Characteristics Table, if applicable.
will remain in the high state (i.e. V
will remain in a low state (i.e. V
OH
I-O
is measured with a DC load current. When driving capacitive load V
< 5 PA). This test is performed before 100% production test for partial discharge (method B) shown in the IEC/EN/DIN EN 60747-5-2
O
PHL
Symbol
R
V
C
< 1.0 V).
ISO
I-O
I-O
O
and t
> 15.0 V).
PLH
ACPL-P302
ACPL-W302
between any two parts or channels under the same test conditions.
Min.
3750
5000
g
Typ.
10
0.6
of the driven IGBT increases.
12
OL
peak.
CM
Max.
CM
/dt| of the common mode pulse, V
OH
/dt| of the common mode pulse V
will approach V
Units
V
pF
rms
Test Conditions
T
RH < 50% for 1 min.
V
Freq=1 MHz
A
I-O
CC
= 25°C,
= 500 V
as I
OH
rms
approaches zero amps.
for 1 second (leakage detection
CM
CM
, to assure that the output
to assure that the output
Fig.
Note
8, 10
9, 10
10
O
peak