HCPL-1931#300 Avago Technologies US Inc., HCPL-1931#300 Datasheet - Page 7
![ISOLAT 1.5KVDC 2CH OPEN 16SMD GW](/photos/15/83/158318/dual_inline_gull_wing_sml.jpg)
HCPL-1931#300
Manufacturer Part Number
HCPL-1931#300
Description
ISOLAT 1.5KVDC 2CH OPEN 16SMD GW
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HCPL-1930300.pdf
(12 pages)
Specifications of HCPL-1931#300
Package / Case
16-SMD, Gull Wing
Voltage - Isolation
1500VDC
Number Of Channels
2, Unidirectional
Current - Output / Channel
25mA
Data Rate
10Mbps
Propagation Delay High - Low @ If
60ns @ 13mA
Current - Dc Forward (if)
60mA
Input Type
AC, DC
Output Type
Open Collector
Mounting Type
Surface Mount
Maximum Continuous Output Current
25 mA
Maximum Fall Time
24 ns
Maximum Forward Diode Current
60 mA
Maximum Rise Time
30 ns
Output Device
Logic Gate Photo IC
Configuration
2 Channel
Maximum Baud Rate
10 MBps
Maximum Forward Diode Voltage
2.75 V
Maximum Reverse Diode Voltage
1.1 V
Maximum Power Dissipation
564 mW
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 55 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Typical Specifications
T
Notes:
10. CM
11. Measured between adjacent input leads shorted together, i.e. between 1, 2 and 4 shorted together and pins 5, 6 and 8 shorted together.
12. No external pull up is required for a high logic state on the enable input.
13. Measured between pins 1 and 2 or 5 and 6 shorted together, and pins 10 through 15 shorted together.
14. Parameters shall be tested as part of device initial characterization and after process changes. Parameters shall be guaranteed to the limits
15. Standard parts receive 100% testing at 25 C (Subgroups 1 and 9). Hi-Rel and SMD parts receive 100% testing at 25, 125, and -55 C (Subgroups 1
7
Parameter
Resistance (Input-Output)
Capacitance (Input-Output)
Input-Input Insulation
Leakage Current
Resistance (Input-Input)
Capacitance (Input-Input)
Propagation Delay Time of Enable
from V
Propagation Delay Time of Enable
from V
Output Rise Time (10-90%)
Output Fall Time (90-10%)
Input Capacitance
1. Bypassing of the power supply line is required, with a 0.1 F ceramic disc capacitor adjacent to each isolator. The power supply bus for the
2. Derate linearly at 1.2 mA/ C above T
3. Each channel.
4. Device considered a two terminal device: pins 1 through 8 are shorted together, and pins 9 through 16 are shorted together.
5. The t
6. The t
7. The t
8. The t
9. CM
A
= 25 C, V
isolators should be separate from the bus for any active loads, otherwise additional bypass capacitance may be needed to suppress regenerative
feedback via the power supply.
the output pulse.
the output pulse.
trailing edge of the output pulse.
leading edge of the output pulse.
V
V
specified for all lots not specifically tested.
and 9, 2 and 10, 3 and 11, respectively).
OUT
OUT
EH
EL
H
L
to V
to V
PLH
PHL
is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state, i.e.
ELH
EHL
is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a high logic state, i.e.
> 2.0 V.
< 0.8 V.
propagation delay is measured form the 6.5 mA point on the trailing edge of the input pulse to the 1.5 V point on the trailing edge of
propagation delay is measured from the 6.5 mA point on the leading edge of the input pulse to the 1.5 V point on the leading edge of
EH
enable propagation delay is measured from the 1.5 V point on the trailing edge of the enable input pulse to the 1.5 V point on the
enable propagation delay is measured from the 1.5 V point on the leading edge of the enable input pulse to the 1.5 V point on the
EL
CC
= 5 V
A
= 100 C.
Symbol
R
C
t
t
C
R
I
ELH
EHL
C
t
t
I-O
I-O
I-I
I-I
I-I
r
f
I
Typ.
0.55
10
10
1.7
0.5
35
35
30
24
60
12
12
Units
nA
pF
pF
pF
ns
ns
ns
ns
Test Conditions
V
f = 1 MHz
V
V
f = 1 MHz
R
I
R
f = 1 MHz, V
I
I-O
I-I
I-I
L
L
= 13 mA, V
65% Relative Humidity,
= 510 , C
= 510 , C
= 500 Vdc, t = 5 s
= 500 Vdc
= 500 V dc
EH
I
L
L
= 0, PINS 1 to 2 or 5 to 6
= 15 pF,
= 15 pF, I
= 3 V, V
EL
I
= 0 V
= 13 mA
Fig.
6, 7
6, 7
Note
3, 13
3, 13
3, 7
3, 8
11
11
11
3
3
3