FODM3023 Fairchild Optoelectronics Group, FODM3023 Datasheet
FODM3023
Specifications of FODM3023
FODM3023FS
FODM3023_NL
FODM3023_NL
Related parts for FODM3023
FODM3023 Summary of contents
Page 1
... NOTE All dimensions are in inches (millimeters) ©2005 Fairchild Semiconductor Corporation FODM3010, FODM3011, FODM3012, FODM3021, FODM3022, FODM3023 Rev. 1.0.0 Description The FODM301X and FODM302X series consists of a GaAs infrared emitting diode driving a silicon bilateral switch housed in a compact 4-pin mini-flat package. The lead pitch is 2.54 mm. ...
Page 2
... This is static dv/dt. See Figure 1 for test circuit Commutating dv/dt is function of the load-driving thyristor(s) only. 3. All devices are guaranteed to trigger between max I (15 mA for FODM3010 and FODM3021 for FODM3011 and FODM3022 for FODM3012 and FT FODM3023) and absolute max I F FODM3010, FODM3011, FODM3012, FODM3021, FODM3022, FODM3023 Rev. 1.0 25°C unless otherwise specified) A Symbol T T ...
Page 3
... 25°C 1 100°C 1.0 0 FORWARD CURRENT (mA) Fig. 3 Holding Current vs. Ambient Temperature 10 NORMALIZED TO T 1.0 0.1 -40 - AMBIENT TEMPERATURE (°C) FODM3010, FODM3011, FODM3012, FODM3021, FODM3022, FODM3023 Rev. 1.0.0 1000 100 10 1 0.1 100 1.6 = 25°C A 1.4 1.2 1.0 0.8 0 100 0.8 -40 3 Fig ...
Page 4
... Fig. 5 LED Current Required to Trigger vs. LED Pulse Width 25° NORMALIZED LED TRIGGER PULSE WIDTH (°C) FODM3010, FODM3011, FODM3012, FODM3021, FODM3022, FODM3023 Rev. 1.0.0 Fig. 6 Off-State Output Terminal Voltage vs. Ambient Temperature 1.4 NORMALIZED 25°C >> 100µs IN 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 -40 100 Fig ...
Page 5
... CC MOC3010 MOC3011 MOC3012 2 Figure 10. Inductive Load with Sensitive Gate Triac (I FODM3010, FODM3011, FODM3012, FODM3021, FODM3022, FODM3023 Rev. 1.0.0 1. The mercury wetted relay provides a high speed repeated pulse to the D.U.T. 2. 100x scope probes are used, to allow high speeds and kΩ voltages. 3. The worst-case condition for static dv/dt is established by ...
Page 6
... The 39 ohm resistor and 0.01 µF capacitor are for snubbing of the triac, and the 470 ohm resistor and 0.05 mF capacitor are for snubbing the coupler. These components may or may not be necessary depending upon the particular and load used. FODM3010, FODM3011, FODM3012, FODM3021, FODM3022, FODM3023 Rev. 1.0.0 180 4 FODM3010 0.2 µ ...
Page 7
... FODM3010, FODM3011, FODM3012, FODM3021, FODM3022, FODM3023 Rev. 1.0.0 Tape and Reel (500 units) Tape and Reel (2500 units) Tape and Reel (500 units; unit 180° rotated) Tape and Reel (2500 units; unit 180° rotated) Tape and Reel (500 units) and VDE Approved Tape and Reel (2500 units) and VDE Approved Tape and Reel (500 units ...
Page 8
... Sprocket Hole Pitch Sprocket Hole Dia. Sprocket Hole Location Pocket Location Pocket Pitch Pocket Dimension Pocket Hole Dia. Cover Tape Width Cover Tape Thickness Max. Component Rotation or Tilt Devices Per Reel Reel Diameter FODM3010, FODM3011, FODM3012, FODM3021, FODM3022, FODM3023 Rev. 1.0 Description Symbol ...
Page 9
... Recommended Infrared Reflow Soldering Profile • Peak reflow temperature: 230°C (package surface temperature) for 30 seconds • Time of temperature higher than 210°C: 60 seconds or less • One time soldering reflow is recommended FODM3010, FODM3011, FODM3012, FODM3021, FODM3022, FODM3023 Rev. 1.0.0 0.024 (0.61) 0.190 (4.83) 0.310 (7.87) ...
Page 10
... PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Advance Information Preliminary No Identification Needed Obsolete FODM3010, FODM3011, FODM3012, FODM3021, FODM3022, FODM3023 Rev. 1.0.0 PowerSaver™ ISOPLANAR™ PowerTrench LittleFET™ QFET MICROCOUPLER™ QS™ MicroFET™ ...