NHD-0216K3Z-FL-GBW Newhaven Display, NHD-0216K3Z-FL-GBW Datasheet - Page 6
![LCD MOD SER CHAR 2X16 Y/G TRANSF](/photos/7/89/78924/nhd-0216k3z-fl-gbw_sml.jpg)
NHD-0216K3Z-FL-GBW
Manufacturer Part Number
NHD-0216K3Z-FL-GBW
Description
LCD MOD SER CHAR 2X16 Y/G TRANSF
Manufacturer
Newhaven Display
Series
NHD-0216K3Z-Fr
Datasheet
1.NHD-0216K3Z-FL-GBW.pdf
(14 pages)
Specifications of NHD-0216K3Z-FL-GBW
Display Type
STN - Super-Twisted Nematic
Display Mode
Transflective
Number Of Digits/alpha
32
Outline L X W X H
80.00mm x 36.00mm x 13.50mm
Viewing Area
64.50mm L x 16.40mm W
Backlight
LED - Yellow/Green
Display Format
16 x 2
Character Size
5.23mm H x 3.00mm W
Character Format
5 x 8 Dots
Voltage - Supply
5.0V
Dot Size
0.56mm W x 0.61mm H
Operating Temperature
-20°C ~ 70°C
Character Count X Line
16 x 2
Module Size (w X H X T)
80 mm x 36 mm x 13.5 mm
Fluid Type
STN
Background Color
Gray
Backlight Type
LED Yellow / Green
For Use With
NHDEV - BOARD DEV LCD COG TFT 100X95MM
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Interface
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Communication Information
This display uses a built‐in PIC 16F690 for serial communication.
I2C protocol:
To enter the I2C mode, place a jumper on R1.
SDA and SDK have pull‐up resistors (10K Ohm) on R7 and R8.
The default I2C address is 80 (50 hex). The I2C address can be changed to any 8‐bit value by command function, with
the exception that the LSB (least significant bit) must always be ‘0’. Once the I2C address has been changed, it will be
saved in the system memory, and it will revert back to the default address if either RS232 or SPI protocol is selected.
The I2C interface is capable of receiving data at up to 100KHz‐clock rate.
SPI protocol:
To enter the SPI mode, place a jumper on R2.
SPI mode has a normally high level idle clock. When Slave Select is LOW, data is sampled on the rising edge of the
Clock.
The SPI interface is capable of receiving data at up to 100KHz‐clock rate.
RS232 protocol:
To enter the RS232 mode, both R1 and R2 should be open.
The RS232 signal must be 5V TTL compatible. Communication format is 8‐bit data, 1 Stop bit, no parity, no hand‐
shaking. Default BAUD rate is 9600, and is changeable with a command function. Once the BAUD rate has been
changed, it will be saved in the system memory, and it will revert back to the default address if either I2C or SPI
protocol is selected.
ASCII TEXT
To display normal text, just enter its ASCII number. A number from 0x00 to 0x07 displays the user
defined custom character, 0x20 to 0x7F displays the standard set of characters, 0xA0 to 0xFD display
characters and symbols that are factory‐masked on the SPLC780D controller. 0xFE is reserved.
[6]