ATAVRDISPLAYX Atmel, ATAVRDISPLAYX Datasheet - Page 346
ATAVRDISPLAYX
Manufacturer Part Number
ATAVRDISPLAYX
Description
KIT EVAL XMEGA DISPLAY
Manufacturer
Atmel
Specifications of ATAVRDISPLAYX
Main Purpose
*
Embedded
*
Utilized Ic / Part
*
Primary Attributes
*
Secondary Attributes
*
Silicon Manufacturer
Atmel
Silicon Family Name
ATxmega
Kit Contents
Board
Features
Temperature Sensor, Mono Speaker Via Audio Amplifier
Svhc
No SVHC (15-Dec-2010)
Core Architecture
AVR
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATAVRDISPLAYX
Manufacturer:
Atmel
Quantity:
135
- Current page: 346 of 445
- Download datasheet (6Mb)
29.3.1
29.3.2
29.3.3
8077H–AVR–12/09
Enabling
Disabling
Frame Format and Characters
The remainder of this section is only intended for third parties developing programming support
for XMEGA.
The PDI Physical must be enabled before it can be used. This is done by first forcing the
PDI_DATA line high for a period longer than the equivalent external reset minimum pulse width
(refer to device data sheet for external reset pulse width data). This will disable the RESET func-
tionality of the Reset pin, if not already disabled by the fuse settings.
In the next step of the enabling procedure the PDI_DATA line must be kept high for 16 PDI_CLK
cycles (16 positive edges detected). The first PDI_CLK cycle must start no later than 100uS
after the RESET functionality of the Reset pin was disabled. If this does not occur in time the
RESET functionality of the Reset pin is automatically enabled again and the enabling procedure
must start over again.
After this the PDI is enabled and ready to receive instructions. The enable sequence is shown in
Figure 29-3 on page
The RESET pin is sampled when the PDI interface is enabled. The RESET register is then set
according to the state of the RESET pin, preventing the device from running code after the reset-
functionality of this pin is disabled.
The PDI_DATA pin has an internal pull-down resistor.
Figure 29-3. Sequence for enabling the PDI.
If the clock frequency on the PDI_CLK is lower than approximately 10 kHz, this is regarding as
inactivity on the clock line. This will then automatically disable the PDI. If not disabled by fuse,
the RESET function on the Reset (PDI_CLK) pin is automatically enabled again. If the time-out
occurs during the PDI enabling sequence, the whole sequence must be started from the
beginning.
This also means that the minimum programming frequency is approximately 10 kHz.
The PDI physical layer uses a fixed frame format. A serial frame is defined to be one character
of eight data bits with start and stop bits and a parity bit.
Figure 29-4. PDI serial frame format.
PDI_DATA
PDI_CLK
(IDLE)
St
Disable RESET function on Reset (PDI_CLK) pin
346.
0
1
2
3
4
FRAME
5
6
7
P
Sp1
Activate PDI
Sp2
XMEGA A
(St/IDLE)
346
Related parts for ATAVRDISPLAYX
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: