ATAVRDISPLAYX Atmel, ATAVRDISPLAYX Datasheet - Page 82
ATAVRDISPLAYX
Manufacturer Part Number
ATAVRDISPLAYX
Description
KIT EVAL XMEGA DISPLAY
Manufacturer
Atmel
Specifications of ATAVRDISPLAYX
Main Purpose
*
Embedded
*
Utilized Ic / Part
*
Primary Attributes
*
Secondary Attributes
*
Silicon Manufacturer
Atmel
Silicon Family Name
ATxmega
Kit Contents
Board
Features
Temperature Sensor, Mono Speaker Via Audio Amplifier
Svhc
No SVHC (15-Dec-2010)
Core Architecture
AVR
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATAVRDISPLAYX
Manufacturer:
Atmel
Quantity:
135
- Current page: 82 of 445
- Download datasheet (6Mb)
7.8
8077H–AVR–12/09
External Clock Source Failure Monitor
Figure 7-6.
When the DFLL is enabled it will count each oscillator clock cycle, and for each reference clock
edge, the counter value is compared to the fixed ideal relationship between the reference clock
and the 1kHz reference frequency. If the internal oscillator runs too fast or too slow, the DFLL
will decrement or increment the corresponding DFLL Calibration Register value by one to adjust
the oscillator frequency slightly. When the DFLL is enabled the DFLL Calibration Register can-
not be written from software.
The ideal counter value representing the number of oscillator clock cycles for each reference
clock cycle is loaded to the DFLL Oscillator Compare Register during reset. The register can
also be written from software to change the frequency the internal oscillator is calibrated to.
The DFLL will stop when entering a sleep-mode where the oscillators are stopped. After wake-
up the DFLL will continue with the calibration value found before entering sleep. For the DFLL
Calibration Register to be reloaded with the default value it has after reset, the DFLL must dis-
abled before entering sleep and enabled the again after leaving sleep.
The active reference cannot be disabled when the DFLL is enabled.
When the DFLL is disabled the DFLL calibration Register can be written from software for man-
ual run-time calibration of the oscillator.
For details on internal oscillator accuracy when the DFLL is enabled, refer to the device data
sheet.
To handle external clock source failures, there is a built-in monitor circuit monitoring the oscilla-
tor or clock used to derive the XOSC clock. The External Clock Source Failure Monitor is
disabled by default, and it must be enabled from software before it can be used. If an external
TOSC1
TOSC2
Figure 5-5. DFLL reference clock selection
32.768 kHz Crystal Osc.
32.768 kHz Int. Osc.
32 MHz Int. Osc.
2 MHz Int. Osc.
DFLL
DFLL
XMEGA A
82
Related parts for ATAVRDISPLAYX
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: