ISL6224EVAL1 Intersil, ISL6224EVAL1 Datasheet
ISL6224EVAL1
Specifications of ISL6224EVAL1
Related parts for ISL6224EVAL1
ISL6224EVAL1 Summary of contents
Page 1
... Refer to Table 2 for the range of input and output voltages and currents. Switch Settings The ISL6224EVAL1 board is shipped with the four position dip switch S1 set for 2.5V output. S1 controls the ENABLE function “EN” and selects the output voltage. Figure 1 illustrates S1 position names and Table 1 describes the function of each switch position ...
Page 2
... FIGURE 2. SOFT-START ON 3.3V OUTPUT (2ms/Div) Output Ripple The ISL6224EVAL1 evaluation board is populated with one 330µF/6.3V SANYO POSCAP output capacitor which has 40mΩ ESR at 100kHz. Figures show the output voltage ripple and phase node voltage when the converter is operating in various modes and various combinations of VIN and Fs ...
Page 3
Evaluation Board Performance Graphs Vin=15 V, Fs= 300kHz Vripple = 34mV FIGURE 3. HYSTERETIC MODE AT ZERO LOAD CURRENT Vin=5 V, Fs=300kHz Vripple = 21mV FIGURE 5. HYSTERETIC MODE AT ZERO LOAD CURRENT 3 Application Note 9983 Vin=15 V, Fs=300kHZ ...
Page 4
Evaluation Board Performance Graphs Vin=5 V, Fs=600kHz Vripple = 19mV Phase Node FIGURE 7. HYSTERETIC MODE AT ZERO LOAD CURRENT ∆V = 98mV Vin=15 V, Fs=300kHz Vout=2.5V, AC Coupled, Load Current FIGURE 9. HYSTERETIC MODE TRANSIENT RESPONSE 4 Application Note ...
Page 5
Evaluation Board Performance Graphs ∆V = 84mV Vin=5 V, Fs=300kHz Load Current FIGURE 11. HYSTERETIC MODE TRANSIENT RESPONSE ∆V Vin=5 V, Fs=600kHz = 84mV Load Current FIGURE 13. HYSTERETIC MODE TRANSIENT RESPONSE 5 Application Note 9983 (Continued) Vin=5 V, Fs=300kHz ...
Page 6
... The value of Ioc and the value of Risen are inserted into the Rocset calculation on page 6 of the ISL6224 data sheet. The ISL6224EVAL1 evaluation board has been adjusted for 3.0 full load amps and approximately 6.3A peak inductor current for over current protection. Figure 15 shows a typical shutdown waveform when the load is over the limit ...
Page 7
... The voltage at the VSEN pin is internally compared to a 0.9V reference voltage and passed on to the next stage of the PWM generation circuits. On the ISL6224EVAL1 evaluation board the two resistor voltage divider feedback network consists of R10 (top resistor) and (R15 or R16 or R17) bottom resistors. Each bottom resistor chooses a different output voltage ...
Page 8
... Pgnd ISL6224 1.0uF FDS6912A 10V 1206 PGND GND PGND C19 0.1 uF 50V 0805 LXA3025IGC Vo#3 ENABLE 1.25V R14 R16 100K 30. 0805 0805 BSS123LT1 SOT23 4 3 FIGURE 20. ISL6224EVAL1 EVALUATION BOARD SCHEMATIC C23 C24 1812 1812 1812 1812 1812 1812 1812 1812 SMB ...
Page 9
... TABLE 4. BILL OF MATERIALS REV B FOR ASSEMBLY ISL6224EVAL1 REFERENCE ITEM QTY UNITS DESIGNATOR CR1 C13 C4, C10 C11 C12 C18, C22, C25 C19 C20 C15 R10 R11, R14, R19 R12, R13 R15 R16 R17 9 Application Note 9983 DESCRIPTION LED, SMD, 4P, POLARIZED, RED/GRN CAP, OSCON, RADIAL, F-SIZE, 56µ ...
Page 10
... TABLE 4. BILL OF MATERIALS REV B FOR ASSEMBLY ISL6224EVAL1 (Continued) REFERENCE ITEM QTY UNITS DESIGNATOR TP1, TP2, TP3 TP4, TP5 J1, J2, J3, J4, J6, J7, J8, J12 JP1, JP2 JP3 JP1, JP2, JP3 C2, C3, C6, C7, C8, C16, C17, C21, C23, C24, D1, D4, L3, U1 Application Note 9983 DESCRIPTION RESISTOR, TF, 0805, 1 ...
Page 11
Silk Screens FIGURE 21. TOP LAYER FIGURE 23. BOTTOM LAYER 11 Application Note 9983 FIGURE 22. SILK SCREEN TOP FIGURE 24. SILK SCREEN BOTTOM ...
Page 12
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...