ATQT600 Atmel, ATQT600 Datasheet - Page 112
ATQT600
Manufacturer Part Number
ATQT600
Description
KIT EVAL TOUCH FOR QT600
Manufacturer
Atmel
Series
QTouch™r
Specifications of ATQT600
Sensor Type
Touch Screen
Interface
USB
Embedded
Yes, Other
Utilized Ic / Part
ATtiny88, ATmega324PA, ATxmega128A1
Processor To Be Evaluated
ATtiny88, ATmega324, ATxmega128
Data Bus Width
8 bit, 16 bit
Interface Type
USB
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
1.6 V to 3.6 V
Silicon Manufacturer
Atmel
Kit Application Type
Sensor
Application Sub Type
Touch Sensor
Kit Contents
USB Bridge, MCU Cards, Touchpad Cards
Svhc
No SVHC (15-Dec-2010)
Mcu Supported Families
ATtiny88,
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Supply
-
Sensitivity
-
Sensing Range
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATQT600
Manufacturer:
Atmel
Quantity:
135
- Current page: 112 of 178
- Download datasheet (4Mb)
6.3.7.2.2
When the External Discharge arrangement is used, a logic-level (DIS) pin is connected to an
external resistor (Rdis) that can be used to control the discharge of the Capacitors. A typical
value for Rdis is 100 kOhm. This value of Rdis will give a discharge current of approximately
1.1V/(100 kOhm) = 11 microAmp. The case C shows this arrangement. The Resistive drive
option on the X and Yk lines can be optionally enabled or disabled with this arrangement. When
the Resistive drive is option is not enabled, it is recommended to use 1kOhm resistors on X and
Yk Lines external to the UC3L device.
6.3.7.2.3
When the SMP Discharge mode arrangement is used, a logic-level (SMP) pin is connected to the
capacitors through external high value resistors for the discharge of the capacitors. The case D
shows this arrangement. The Resistive drive option on the X and Yk lines can be optionally
enabled or disabled with this arrangement. When the Resistive drive is option is not enabled, it is
recommended to use 1kOhm resistors on X and Yk Lines external to the UC3L device.
6.3.7.2.4
The VDIV pin provides an option to make ACREFN a small positive voltage if required. The VDIV
pin is driven when the analog comparators are in use, and this signal can be used along with a
voltage divider arrangement to create a small positive offset on the ACREFN pin. The VDIVEN
option can be used optionally with any of the QMatrix modes discussed in the previous sections.
Typical values for Ra and Rb are Ra=16500 ohm and Rb = 50 ohm. Assuming a 3.3V I/O supply,
this will shift the comparator threshold by 3.3V*(Rb/(Ra+Rb)) which is 10 mV. The VDIVEN pin
option usage in the Internal Discharge mode scenario is shown in case E.
6.3.7.2.5
In order to prevent interference from the 50 or 60 Hz mains line the CAT can optionally trigger
QMatrix acquisition on the external SYNC input signal. The SYNC signal should be derived from
the mains line and the acquisition will trigger on a falling edge of this signal. The SYNC pin
option can be used with any of the QMatrix modes discussed in the previous sections. The
SYNC pin usage in the Internal Discharge mode scenario is shown in case F.
For QMatrix method SMP, DIS, VDIV and SYNC pin options discussed in this Section, Refer to
Section
112
6.3.15.2.13.
SMP Discharge Mode
VDIVEN Voltage Divider Enable option
External Discharge mode
SYNC pin option
8207J-AT42-02/11
Related parts for ATQT600
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: