Z8F08200100KITG Zilog, Z8F08200100KITG Datasheet - Page 196
Z8F08200100KITG
Manufacturer Part Number
Z8F08200100KITG
Description
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer
Zilog
Series
Z8 Encore!®r
Type
MCUr
Datasheets
1.Z8F08200100KITG.pdf
(18 pages)
2.Z8F08200100KIT.pdf
(264 pages)
3.Z8F08200100KITG.pdf
(9 pages)
Specifications of Z8F08200100KITG
Contents
Evaluation Board, Cable, Power Supply, Software and Documentation
Silicon Manufacturer
Zilog
Core Architecture
Z8 Encore
Silicon Core Number
Z8F0822SJ020
Silicon Family Name
XP F0822
Rohs Compliant
Yes
For Use With/related Products
Z8 Encore!™
For Use With
269-4661 - KIT ACC ETHERNET SMART CABLE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
269-4630
- Current page: 196 of 264
- Download datasheet (6Mb)
Table 95. OCD Status Register (OCDSTAT)
PS022517-0508
BITS
FIELD
RESET
R/W
OCD Status Register
IDLE
automatically set to 1. If this bit is set, the OCDCNTR register does not count when the
CPU is running.
0 = OCDCNTR is setup as counter
1 = OCDCNTR generates hardware break when PC == OCDCNTR
BRKZRO—Break when OCDCNTR ==
If this bit is set, then the OCD automatically sets the DBGMODE bit when the OCD-
CNTR register counts down to
when the part leaves DEBUG Mode.
0 = OCD does not generate BRK when OCDCNTR decrements to 0000H
1 = OCD sets DBGMODE to 1 when OCDCNTR decrements to 0000H
Reserved
These bits are reserved and must be 0.
RST—Reset
Setting this bit to 1 resets the Z8 Encore! XP
through a normal POR sequence with the exception that the OCD is not reset. This bit is
automatically cleared to 0 when the reset finishes.
0 = No effect.
1 = Reset the Z8 Encore! XP F0822 Series device.
The OCD Status register reports status information about the current state of the debugger
and the system.
IDLE—CPU Idling
This bit is set if the part is in DEBUG mode (DBGMODE is 1), or if a BRK instruction
occurred since the last time OCDCTL was written. This can be used to determine if the
CPU is running or if it is idling.
0 = The eZ8 CPU is running.
1 = The eZ8 CPU is either stopped or looping on a BRK instruction.
HALT—HALT Mode
0 = The device is not in HALT mode.
1 = The device is in HALT mode.
7
HALT
6
RPEN
5
0000H
4
. If this bit is set, the OCDCNTR register is not reset
R
0
0000H
®
F0822 Series device. The device goes
3
Reserved
Z8 Encore! XP
2
Product Specification
1
®
On-Chip Debugger
F0822 Series
0
183
Related parts for Z8F08200100KITG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: