C8051F410DK Silicon Laboratories Inc, C8051F410DK Datasheet - Page 102

• Manufacturer Part Number: C8051F410DK
• Description: KIT DEV FOR C8051F41X
• Manufacturer: Silicon Laboratories Inc
• Type: MCUr

Specifications of C8051F410DK

• Contents: Evaluation Board, Power Supply, USB Cables, Adapter and Documentation
• Processor To Be Evaluated: C8051F41x
• Interface Type: USB
• Silicon Manufacturer: Silicon Labs
• Core Architecture: 8051
• Silicon Core Number: C8051F410
• Silicon Family Name: C8051F41x
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With/related Products: Silicon Laboratories C8051F41x
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1314

C8051F410/1/2/3
10.3.1. Idle Mode
Setting the Idle Mode Select bit (PCON.0) causes the CIP-51 to halt the CPU and enter Idle mode as soon
as the instruction that sets the bit completes execution. All internal registers and memory maintain their
original data. All analog and digital peripherals can remain active during Idle mode.
Idle mode is terminated when an enabled interrupt is asserted or a reset occurs. The assertion of an
enabled interrupt will cause the Idle Mode Selection bit (PCON.0) to be cleared and the CPU to resume
operation. The pending interrupt will be serviced and the next instruction to be executed after the return
from interrupt (RETI) will be the instruction immediately following the one that set the Idle Mode Select bit.
If Idle mode is terminated by an internal or external reset, the CIP-51 performs a normal reset sequence
and begins program execution at address 0x0000.
If enabled, the Watchdog Timer (WDT) will eventually cause an internal watchdog reset and thereby termi-
nate the Idle mode. This feature protects the system from an unintended permanent shutdown in the event
of an inadvertent write to the PCON register. If this behavior is not desired, the WDT may be disabled by
software prior to entering the Idle mode if the WDT was initially configured to allow this operation. This pro-
vides the opportunity for additional power savings, allowing the system to remain in the Idle mode indefi-
nitely, waiting for an external stimulus to wake up the system.
10.3.2. Stop Mode
Setting the Stop Mode Select bit (PCON.1) causes the CIP-51 to enter Stop mode as soon as the instruc-
tion that sets the bit completes execution. In Stop mode the internal oscillator, CPU, and all digital peripher-
als are stopped; the state of the external oscillator circuit is not affected. Each analog peripheral (including
the external oscillator circuit) may be shut down individually prior to entering Stop Mode. Stop mode can
only be terminated by an internal or external reset. On reset, the CIP-51 performs the normal reset
sequence and begins program execution at address 0x0000.
If enabled, the Missing Clock Detector will cause an internal reset and thereby terminate the Stop mode.
The Missing Clock Detector should be disabled if the CPU is to be put to in STOP mode for longer than the
MCD timeout period of 100  s.
10.3.3. Suspend Mode
The C8051F41x devices feature a low-power SUSPEND mode, which stops the internal oscillator until a
wakening event occurs. See
102
Bits7–2: Reserved.
Bit1:
Bit0:
Reserved Reserved Reserved Reserved Reserved Reserved
R/W
Bit7
STOP: STOP Mode Select.
Writing a ‘1’ to this bit will place the CIP-51 into STOP mode. This bit will always read ‘0’.
1: CIP-51 forced into power-down mode. (Turns off internal oscillator).
IDLE: IDLE Mode Select.
Writing a ‘1’ to this bit will place the CIP-51 into IDLE mode. This bit will always read ‘0’.
1: CIP-51 forced into IDLE mode. (Shuts off clock to CPU, but clock to Timers, Interrupts,
and all peripherals remain active.)
R/W
Bit6
SFR Definition 10.7. PCON: Power Control
R/W
Bit5
Section “19.1.1. Internal Oscillator Suspend Mode” on page 166
R/W
Bit4
Rev. 1.1
R/W
Bit3
R/W
Bit2
STOP
R/W
Bit1
SFR Address: 0x87
IDLE
R/W
Bit0
00000000
Reset Value
.