@Super low ESR, impedance and high heat resistance have been obtained by using con-
@Suitable for DC-DC converters, voltage regulators and decoupling applications.
@Endurance : 125C 1,000 hours
@Rated voltage range : 2.5 to 20V
@Case size range : F6.3B5.7L to F10B7.7L
@RoHS Compliant
?SPECIFICATIONS
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
?PART NUMBERING SYSTEM
A P X H
?DIMENSIONS [mm]
@Terminal Code : A
1
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Bias Humidity
Surge Voltage
Failure Rate
ductive polymer as electrolyte.
2
3
Items
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 125C.
LP0.3
4
0.3max.
A A A
5
6
7
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
A R A
8
9
-55 to +125C
2.5 to 20V
P20% (M)
Rated voltageB1.15
Shall not exceed values shown in STANDARD RATINGS.
0.12 max.
Z(-25C)/Z(+20C)[1.15
Z(-55C)/Z(+20C)[1.25
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 1,000 hours
at 125C.
Appearance
Capacitance change
DF (tanE)
ESR
Leakage current
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at
60C, 90 to 95% RH for 1,000 hours.
Appearance
Capacitance change
DF (tanE)
ESR
Leakage current
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 125C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
Capacitance change
DF (tanE)
ESR
Leakage current
0.5% per 1,000 hours maximum (Confidence level 60% at 125C)
10
A A A
11
W
AP0.2
12 13
dc
M
14
dc
A A A
, Capacitance range : 22 to 1,000MF
15
Capacitance code (ex. 22MF:220,100MF:101)
16 17
G
18
Voltage code (ex. 6.3V:6R3,10V:100)
No significant damage
[P20% of the initial value
[200% of the initial specified value
[200% of the initial specified value
[The initial specified value
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
Size code
Capacitance tolerance code
F60
H70
J80
6.3
fD
10
Supplement code
8
Terminal code
5.7
6.7
7.7
Taping code
Series code
L
Size code
Category
(1/2)
10.3
6.6
8.3
A
Characteristics
10.3
6.6
8.3
B
Please refer to "Product code guide (conductive polymer type)"
11.0
7.2
9.0
C
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
W
1.9
3.1
4.5
P
PXH
PXA
Higher temperature
CAT. No. E1001K
(at 20C after 2 minutes)
?MARKING
EX) 20V22MF
Surface Mount
(at 20C, 120Hz)
(at 20C, 120Hz)
H
22
20
(at 100kHz)
39F
(at 125C)
V