mic4422a Micrel Semiconductor, mic4422a Datasheet
mic4422a
Available stocks
Related parts for mic4422a
mic4422a Summary of contents
Page 1
... General Description MIC4421A and MIC4422A MOSFET drivers are rugged, efficient, and easy to use. The MIC4421A is an inverting driver, while the MIC4422A is a non-inverting driver. Both versions are capable of 9A (peak) output and can drive the largest MOSFETs with an improved safe operating margin. The MIC4421A/4422A accepts any logic input from 2 ...
Page 2
... MIC4421AAM* MIC4421ABM MIC4421AYM MIC4421ACM MIC4421AZM MIC4421ABN MIC4421AYN MIC4421ACN MIC4421AZN MIC4421ACT MIC4421AZT MIC4422AAM* MIC4422ABM MIC4422AYM MIC4422ACM MIC4422AZM MIC4422ABN MIC4422AYN MIC4422ACN MIC4422AZN MIC4422ACT MIC4422AZT * Special order. Contact factory. Pin Configuration GND 8-Pin PDIP (N) 8-Pin SOIC (M) Pin Description Pin Number Pin Number ...
Page 3
... PDIP (θ SOIC (θ TO-220 (θ PDIP (θ SOIC (θ TO-220 (θ < +125°C, unless noted. A Condition (MIC4422A (MIC4421A (MIC4422A (MIC4421A See Figure 3 See Figure 3 0V ≤ V ≤ See Figure 1 See Figure 10mA 18V ...
Page 4
... OUTPUT 1.5V 2.1V Figure 3. Input Hysteresis 4 Min Typ 18V S 0.1µF 0.1µ OUT 10,000pF MIC4422A 5V 90% 10 90% 10% 0V Figure 2. Non-Inverting Driver Switching Time Logic MIC4421A/4422A Max Units ...
Page 5
Micrel, Inc. Typical Characteristics June 2007 5 MIC4421A/4422A M9999-062707 ...
Page 6
Micrel, Inc. Typical Characteristics (continued) June 2007 6 MIC4421A/4422A M9999-062707 ...
Page 7
... Functional Diagram 0.1mA IN Functional Description Refer to the functional diagram. The MIC4422A is a non-inverting driver. A logic high on the IN produces gate drive output. The MIC4421A is an inverting driver. A logic low on the IN produces gate drive output. The output is used to turn on an external N- channel MOSFET. ...
Page 8
... MIC4422A Figure 5. Direct Motor Drive 1N4448 (x2) V +15V IN 0.1µF 50V MIC4422A 0.1µF WIMA MKS2 United Chemcon SXE June 2007 To guarantee low supply impedance over a wide frequency range, a parallel capacitor combination is recommended for supply bypassing. Low inductance ceramic disk capacitor swith short lead lengths (< 0.5 inch) should be used. A 1µ ...
Page 9
Micrel, Inc. Input Stage The input voltage level of the MIC4421A changes the quiescent supply current. The N-Channel MOSFET input stage transistor drives a 320µA current source load. With a logic “1” input, the quiescent supply current is typically 500µA. ...
Page 10
Micrel, Inc. Table 1. MIC4421A Maximum Operating Frequency V S 18V 15V 10V 5V Conditions: θ 150°C 25° 10,000pF L Capacitive Load Power Dissipation Dissipation caused by a capacitive load ...
Page 11
Micrel, Inc Power dissipated in a driver when the output T changes states (“shoot-through current”) in Watts. NOTE: The “shoot-through” current from a dual transition (once up, once down) for both drivers is stated in Figure 7 in ...
Page 12
Micrel, Inc. Package Information 0.018 (0.57) June 2007 PIN 1 DIMENSIONS: INCH (MM) 0.380 (9.65) 0.370 (9.40) 0.135 (3.43) 0.125 (3.18) 0.380 (9.65) 0.130 (3.30) 0.320 (8.13) 0.100 (2.54) 0.0375 (0.952) 8-Pin Plastic DIP (N) 8-Pin SOIC (M) 12 MIC4421A/4422A ...
Page 13
Micrel, Inc. MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no ...